Read carefully these instructions before any use.
USA - HZ Mobile Transmitter 1 channel - 2008805
- Power supply is not required for saving data.
- Data need not be programmed once again when the cell is
changed.
- Do not recharge the battery.
- Please separate and dispose of the appliance, batteries
and used batteries at a recycling location.
25mm
63/64
inch
13mm
33/64
inch
40mm
37/64
1
inch
125mm
4
59/64
inch
3mm
1⁄8
inch
3mm
1s
1s
1s
0%
100%
I.P
STOP/
I.P
6m max.
20ft ma x
14°F(-10°C)
140°F(+60°C)
IP30
Transmission
indicator Led
PROG
2 s.
PROG
2 s.
5125969A
For more complete information about programming, please refer to the instructions of the motor used.
Refer to Hz motor instructions to make sure it has this feature.
- For group controls from the new transmitter, repeat operations 1.1 and 1.2 for each motor of the group.
- For main controls from the new transmitter, repeat operations 1.1 and 1.2 for each motor of the installation.
- To delete a transmitter from the memory of a motor, perform operation 1.1 with a programmed transmitter, then perform operation 1.2 with the transmitter to be
deleted.
1.1. Open the memory of the motor using its individual control transmitter:
- Press the Prog. Button for about 3 sec. on the motor’s individual control transmitter, the motor will jog.
1.2. Then validate the operation from the new transmitter to be programmed:
- Press the Prog. Button for about 1 sec. on the new transmitter, the motor will jog.
-
Compatible with motors & receivers
- Wireless switch/class III – Protection Index: IP30
- Maximum transmission time: 10 seconds
- Operating temperature: 14
o
F (-10
o
C) to 140
o
F (60
o
C)
- Storage temperature: -22
o
F (-30
o
C) to 158
o
F (70
o
C)
- Transmitter range: 20ft max. (6m max) throught 2 concrete walls in normal
- Power: 3V lithium battery type CR 2430. Lifetime ± 3 years when 4 pressures of 1s./day
.
- Keep away from children
- Do not position the transmitter near metal in order to ensure its proper operation and
prevent reduced range
- A radio appliance using the same frequency (for example : hi-fi radio headphones)
may deteriorate our product’s performance.
- Do not immerse the product, avoid splashing of liquids.
- Do not use abrasive products or solvents to clean the product.
- Frequency: 433.420 MHz
Adding the transmitter to an existing installation
1
Programming and use Intermediate Position (I.P):
2
Technical data
3
Replacing the battery
FCC
4
5s
Programming:
- Move the motor to the desired position.
- Press 5 seconds on the
STOP
button.
The motor will jog.
0.5s
Use:
- Press the
STOP
button for 0.5 second. The motor runs to the
intermediate position.
S.A.S. au capital de 5 000 000 € - Z.I. Les Giranaux - BP71 - F70103 Arc-Les-Gray CEDEX - RCS VESOUL B 425 650 090 - SIRET 425 650 090 00011 - n° T.V.A CEE FR 87 425 650 090
I.P= Intermediate position
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions
- This device may not cause harmful interference and
- This device must accept any interference received, including interference that may cause undesired operation
Warning! Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment.
