Simrad GO XSE Series Operator'S Manual Download Page 113 | Manualshive

Page: 113 / 242

background image

Adjusting the radar image

The radar image can be improved by adjusting the gain, by filtering
out unwanted echoes due to sea clutter, rain or other weather
conditions, and by tuning the sensitivity of the radar receiver.
You can adjust the gain, sea clutter, and rain clutter by selecting the
relevant icon in the top right corner of the radar panel or from the
radar panel main menu.

Ú

Note:

The radar image settings do not affect the AIS targets.

Sea and rain clutter can be present at the same time, and further
degradation in detection performance will be experienced. As sea
clutter is related to short range and rain clutter is usually present in a
longer range, rain clutter settings can be adjusted without affecting
the echoes in the sea clutter area.
The radar image can be adjusted as described in the next sections.

Radar modes

Use modes are available with preset control settings for different
environments. Not all modes are available for all radar models.

Custom mode

All radar controls can be adjusted and will be retained after a mode
change or radar power cycle. Radar defaults are set for general
purpose use.

Harbor mode

The radar settings are optimized for areas such as busy waterways
and large man-made structures where good target discrimination
and rapid image updates are needed.

Offshore mode

The radar settings are optimized for offshore sea conditions and
making isolated targets larger and easy to see.

Weather mode

The radar settings are optimized for best detection and presentation
of rain clutter. Image update rate is slowed and color depth is
increased.

Radar

| GO XSE/XSR Operator Manual

113

«
...
111
112
113
114
115
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: NORLUX Pages: 2

Brand: VeEX Pages: 2

Brand: JB-Lighting Pages: 48

Brand: NAD Pages: 10

Brand: Rangevision Pages: 28

Tablet1000 Series

Brand: Hantek Pages: 98

Brand: Nemalux Pages: 6

Brand: OBDLink Pages: 2

Brand: Laserworld Pages: 8

Brand: Laserworld Pages: 6

Brand: LaserLiner Pages: 56

Brand: LaserLiner Pages: 54

Brand: Nabtesco Pages: 26

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology...

Brand: M-Audio Pages: 25

FLOOReco 5164-040120

Brand: DOTLUX Pages: 10

Brand: Jumil Pages: 78

Brand: EFX Pages: 2

Brand: RAB Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands