manualshive.com logo in svg

Simrad CA42, Manual

Share
Download
Simrad CA42 Manual Download Page 115

CA4

2/50

/52 Radar operation

Chapter 8

115

                         Standard radar display               Secondary radar display

To make adjustments in the standard radar display (left half of screen):

ADJ

Open for adjustment

- by pressing [ADJ] again will toggle between 1

st

and 2

nd

half of

control panel.

Use the cursor key to move around in the control panel

- and toggle between available values with the +/- keys, and insert data
by the numerical keys.

ENT

Confirm changes by pressing

[ENT] 

or

[MENU]

To make adjustments in the second radar display (right half of screen):

WIN

Go to the second radar display

Carry out adjustments by using the same procedures as mentioned
above for the standard radar display, except for the guard zone which is
not available in the secondary radar display.

)

Indication of HDG (heading) and Rpm (scanner rotation speed) is

only available in full screen presentation.

Summary of Contents for CA42





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands