background image

READ ALL INSTRUCTIONS BEFORE USING MACHINE

When using the sewing machine, basic safety precautions should always be followed, including
the following:

DANGER

- To reduce risk of electric shock:

1. The sewing machine should never be left unattended when plugged in. 
2. Always unplug this sewing machine from the electrical outlet immediately after using and

before cleaning.

3. Always unplug before changing the light bulb. Replace bulb with same type rated 15 watts.

WARNING

- To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Do not allow this machine to be used as a toy. Close attention is necessary when the

sewing machine is used by or near children.

2. Use this sewing machine only for its intended use as described in this manual. Use only

accessories recommended by the manufacturer as contained in this manual.

3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working

properly, if it has been dropped or damaged, or dropped into water. Return the sewing
machine to the nearest authorized dealer or service center for examination, repair, and
electrical or mechanical adjustment.

4. Never operate the sewing machine with any of the air openings blocked. Keep the ventila-

tion openings of the sewing machine and foot controller free from the accumulation of lint,
dust and loose cloth.

5. Never drop or insert any object into any openings.
6. Do not use this machine outdoors.
7. Do not operate this machine where aerosol spray products are being used or where oxygen

is being administered.

8. To disconnect, turn the main switch to the off position then remove the plug from the outlet.
9. Do not unplug by pulling on the cord. To unplug, grasp the plug and pull, not the cord.

10. Keep fingers away from all moving parts. Special care is required around the sewing

machine needle.

11. Always use the proper needle plate. The wrong plate can cause the needle to break.
12. Do not use a bent needle.
13. Do not pull or push the fabric while stitching. It may deflect the needle causing it to break.
14. Switch the sewing machine to the off position when making any adjustments in the needle

area, such as threading the needle, changing the needle, threading the bobbin, or changing
the presser foot.

15. Always unplug the sewing machine from the electrical outlet when removing covers,

lubricating, or when making any other user service adjustments mentioned in this
instruction manual.

SAVE THESE INSTRUCTIONS

This sewing machine is intended for household use.

IMPORTANT SAFETY INSTRUCTIONS

1

Summary of Contents for DenimStar sw210




































Reviews: