background image

     19

TROUBLESHOOTING GUIDE

While normal care and routine maintenance will extend the life of 
your rototiller, prolonged or constant use may eventually require 
that service be performed to allow it to continue operating properly. 
The troubleshooting guide below lists the most common problems, 
causes and remedies.

PRACTICE SAFETY AT ALL TIMES. ENGINE MUST BE 
TURNED OFF AND ALLOWED TO COOL, AND SPARK 
PLUG WIRE MUST BE DISCONNECTED AND SECURED 
BEFORE ATTEMPTING ANY MAINTENANCE OR 
REPAIR.

FAILURE TO COMPLY WITH THIS SAFETY  REQUIREMENT 
CAN RESULT IN SERIOUS PERSONAL INJURY TO YOU 
OR BYSTANDERS.

PROBLEM

REMEDY/ACTION

Engine will not start

Engine runs rough, 

 during operation

Engine is hard to start

Engine misses or lacks power

Engine will not stop when throttle control is positioned at 
stop

Tiller moves forward during starting

Tiller is difficult to control when tilling
(machine jumps or lurches forward)

Tines turn, wheels do not turn

Tines turn, wheels turn, tiller does not move

s!DD

 gas to gas tank.

s#ONNECT

 spark plug wire to spark plug

s4HROTTLE

 must be positioned at choke for a cold start

 

s#LEAN

 or replace air cleaner

s$

rain  old fuel and replace with fresh. Use gas stabilizer 

  at end of season

s-A

ke  sure spark plug wire is securely attached to spark  

 plug

s$

rive  safety control levers must be released to neutral  

  position to start the engine

s2AISE

 the tines for shallow tilling by lowering the depth  

 regulator 

lever

s2EM

ove  and clean fuel tank

s#LEAN

 or replace air cleaner

s)MPROPER

 carburetor adjustment, take to authorized  

 

  engine service center

s2EPLACE

 spark plug and adjust gap

s$

rain  and 

 gas tank and carburetor

s3EE

 engine manual to check and adjust throttle linkage

s$

rive  safety control levers must be released to neutral  

  position to start the engine

s,O

ck  wheels in tilling position

s2AISE

 the tines for shallower tilling by lowering the  

 

  depth regulator lever

s,O

ck  wheels in tilling position

s)NTE

rnal  transmission failure, see your dealer

s,

ower  the tines for deeper tilling by raising the depth  

 regulator 

lever

WARNING

!

Maintenance

Not 

for  

Reproduction

Summary of Contents for 1695577

























Reviews: