background image

13

Regular Maintenance

There are two grease fittings on the auger shaft (Figure
15). Wipe the fittings clean and apply grease, using a
grease gun. Also apply grease on other points indicated.

Apply medium weight (10W) oil to points shown(See
Figures 14 - 16). 

Generally, all moving metal parts should be oiled where
contact is made with other parts. Keep oil and grease off
belts, pulley grooves, drive disc, and friction disc.

See lubrication notes at bottom of page.

IMPORTANT NOTE

It is very important that grease fittings on the auger
shaft are lubricated regularly. If auger rusts to shaft,
damage to worm gear may occur if shear pins do not
break.

To prevent wheels rusting to axles, it is also necessary
to remove the wheels and grease the axles regularly.

LUBRICATION

Figure 14. Drive Area Lubrication Points

(Bottom Cover Removed)

Figure 15. Snowthrower General Lubrication Points

LUBRICATION NOTES:

1.

Grease locations indicated by grease gun symbol:
Use grease fittings when present. Disassemble parts to apply grease to moving parts when grease fittings 
are not installed.

2.

Oil locations indicated by oil can symbol:
Do not allow oil to drip onto traction drive or friction disc.

Friction Disc

Drive Disc

Figure 16. Chute Control Rod Gears

01

Summary of Contents for 1693161





























Reviews: