manualshive.com logo in svg

Simplicity 1691521, Operator'S Manual

Share
Download
Simplicity 1691521 Operator'S Manual Download Page 25

21

Figure 39. Installing Lift Rod to Manual Lift Lever
A. Front Attachment Lift Rod

C. Spring Clip

B.  Manual Lift Lever

A

B

C

Install the Spring Assist

NOTE: The parts described in the following steps (and
shown in Figures 42 & 41) are packaged with the hitch
assembly.

NOTE: 4-link chain replaces 3-link chain supplied with
snowthrower.

1. Place snowthrower in the down position. 

NOTE: On single cylinder engines, the clevis pin (B,
Figure 41) must be installed to the bracket before mount-
ing onto the tractor frame.

2. See Figure 41. Install the spring assist bracket (A)

into the underside of the frame as shown using a 1-
1/4” long capscrew, lockwasher, and nut.

3. See Figure 41. Place the clevis pin (B) through the

spring assist bracket from the back.  Install a flat
washer (C), the 4 link chain (D), another flat washer
(C), and safety clip (E) as shown.

4. Place snowthrower in fully raised position.  

5. Rotate the spring assist lever (A, Figure 42) fully back

and install the spring (B) on the lever and through the
chain.  See Figure 42.

7. Rotate lever forward so that it travels “over center” to

the fully forward position.

8. Lower the snowthrower.

Adjust, Lubricate, and Test Run

1. Adjust the Lift Rod- See Adjustments

2. Adjust the Skids-See Adjustments

3. Lubricate the Snowthrower-See Maintenance.

4. Install the reflectors on the on the rear lip of the seat

deck.  If a snowcab is also installed, make sure the
reflectors are not obstructed.  

5. Test run and recheck belt tension.

Figure 40. Installing Lift Rod to Snowthrower
A. Rod Guide Assembly
B. Hair Pin Clip

Install lift rod to inside of bracket as shown.

A

B

WARNING

Never pull spring-assist tension lever back unless
snowthrower is in fully raised position.

Figure 42. Spring-Assist Lever
A. Lever

B. Spring

Broadmoor-Snowthrower Installation

Frame hole is located on front, left side; in front of engine

Figure 41. Spring Assist Bracket
A. Bracket

D. 4-link Chain

B. Clevis Pin

E. Safety Clip

C. Flat Washer

A

B

D

C

C

E

Summary of Contents for 1691521





































Reviews:

No comments

Brands by name

Popular brands

Load more brands