manualshive.com logo in svg

Simplicity 1691521, Operator'S Manual, Page: 18 / 36

Share
Download
Simplicity 1691521 Operator'S Manual Download Page 18

14

SNOWTHROWER INSTALLATION

1. See Figure 19. Align snowthrower bracket (D) with

front tractor hitch arms (B). Lift snowthrower so that
up-stop brackets (E) rest on hitch arms (B). 

2. Before attaching snowthrower bracket to the hitch,

install the belt from the hitch idler pulley (B, Figure
20) to the snowthrower pulley as shown in Figure 20. 

Do not attempt to install the belt on electric clutch pul-
ley at this time.

3. See Figure 19. Attach snowthrower bracket (D) to

hitch using clevis pins (B) and safety clips (A).

Figure 19. Snowthrower Installation
A. Safety Clips

D. Snowthrower Bracket

B. Hitch Arms

E. Up-Stop Brackets

C. Clevis Pin

Figure 20. Belt Routing
A. V-pulley

C. Electric Clutch Pulley (V-Pulley)

B. Idler Pulley

D. Snowthrower Pulley (V-Pulley)

E. Backside Idler Pulley

D

B

A

C

PTO Belt Installation and Trunion
Adjustment.

1. See Figure 21. To install the belt on the electric

clutch pulley, the trunion (A) on the tension spring
assembly (B) must be fully forward. Turn the handle
(C) to move the trunion forward and slacken the belt.
If the belt is still too tight, loosen the capscrew (D)
and slide the pulley (E) forward to further slacken the
belt.  Install belt on electric clutch pulley. Refer to
Figure 20 for belt routing.   

2. See Figure 21. Re-tighten the pulley (E) and cap-

screw (D) if they were loosened.  Turn the handle (C)
so that the trunion (A) is centered between the marks
as shown.  

NOTE: If trunion cannot be centered between marks,
loosen the trunion (A), loosen the capscrew (D) and
reposition the pulley (E) further rearward. Re-tighten cap-
screw (D) and center the trunion.

Figure 21. Belt Installation & Adjustment
A. Trunion

D. Capscrew

B. Tension Spring Assembly.. E.

Pulley

C. Handle

CAUTION

After snowthrower installation if the tractor hood is
opened, it will come into contact with the
snowthrower.  To protect the hood finish cover the
discharge chute with a towel or blanket.

E

E

Regent-Hitch Installation

Summary of Contents for 1691521





































Reviews:

No comments