TP0332/2
D.1
SRP8000 SERIES VHF/UHF PORTABLE RADIO
APPENDIX D - ALIGNMENT TOOL
INTRODUCTION
Purpose of this Section
This section will help with the installation of the SRP8000 Series Alignment Tool. It lists the
equipment required and how to set-up the PC to get optimum performance from the Alignment Tool. It also
describes how to get started in connecting and aligning a radio.
Purpose of Alignment Tool
The Simoco SRP8000 Series Alignment Tool is used to align the RF circuitry within a SRP8000
Series radio. It may also be used to modify a radio’s hardware code (in the event that the radio’s hardware
has been upgraded).
The Alignment Tool cannot be used for the alignment of radios other than SRP8000 Series radios.
Components Associated with Alignment Tool
To use the alignment tool, a programming lead (0000 321 60001) and a radio test interface unit
(0000 693 20001) are required.
In addition, the Alignment Tool operations require various items of test equipment; these are listed
on page 4.6 Test Equipment in this Service Manual.
Alignment Tool Requirements
To install and use the Alignment Tool it is necessary to have compatible hardware and software.
Hardware Requirement
The computer that the Alignment Tool is to be installed on, must meet certain requirement criteria.
These criteria are classified as follows:
✔
Compulsory requirement; must have this to install and use Alignment Tool.
≥
Recommended minimum requirement; this is the minimum specification to achieve
‘useable’ performance and may be upgraded to achieve better performance.
≈
Optional requirement; provides defined options in using the Alignment Tool.
Table D.16 Hardware Requirements
Note: Whilst the criteria in Table D.1 are a useful guide, it is recommended that the Alignment
Tool should be installed on the highest specification PC available, for optimum
performance.
Specification
Aspect
Criteria
Category
Comment
Computer
IBM™ compatible PC
✔
Processor
486, 33MHz clock
speed
≥
Absolute minimum = 386, 20MHz
RAM
8Mb
≥
Absolute minimum = 4Mb
Hard Disk Space
10Mb free
✔
Floppy Disk Drive
3,5”, 1.44Mb
✔
Required for installation
Display Resolution
At least 640 x 480
✔
Graphics Mode
At least VGA
✔
CGA and XGA not compatible
Display Type
Colour
✔
Mono display: some fields may be
unreadable
Serial Ports
At least one
✔
Necessary for interaction with radio
Other Ports
Additional serial port
≈
Necessary if using a mouse (see Mouse)
Mouse
Mouse connected
≈
Provides alternate method of access to
screen functions.
Summary of Contents for SRP8000 SERIES
