Simex SUR-W410, User Manual

Page: 51 / 60

User manual - METER SUR-W410
Register Write Range Register description
4Ch 6 Yes 0 ÷ 999
“toFF” parameter in “rEL4” menu, expressed in tenth of seconds
or tenth of minutes depend on “unit” parameter - register no. 4Dh)
4Dh 6 Yes 0 ÷ 1
“unit” parameter in “rEL4” menu:
0 - seconds; 1 - minutes
4Eh
6
Yes 0 ÷ 2 “AL” parameter in “rEL4” menu: 0 - no changes; 1 - on; 2 - off
4Fh 6 Yes -999 ÷ 9999 “ SEt2 ” parameter in “ rEL4 ” menu, no decimal point included
50h Yes 0 ÷ 1
“ modE ” parameter in “ HOLd ” menu (type of detected changes):
0 - peaks; 1 - drops
51h Yes 0 ÷ 9999
“ PEA ” parameter in “ HOLd ” menu (minimum detectable change, no
decimal point included)
52h Yes 0 ÷ 199
“ timE ” parameter in “ HOLd ” menu, maximum peaks' (or drops')
display time expressed in seconds
53h Yes 0 ÷ 1
“ HdiS ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
54h 6 Yes 0 ÷ 1
“ H r1 ” parameter in “ HOLd ” menu :
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
55h
6
Yes 0 ÷ 1
“ H r2 ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
56h 6 Yes 0 ÷ 1
“ H r3 ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
57h 6 Yes 0 ÷ 1
“ H r4 ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
58h
1
Yes 0 ÷ 1
“ HOUt ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
70h 5 Yes -999 ÷ 1999
The value of „ X ” coordinate of point no. 1 of the user defined
characteristic, expressed in 0.1%
71h 5 Yes -999 ÷ 9999
The value of „ Y ” coordinate of point no. 1 of the user defined
characteristic, no decimal point included
72h
5
÷ 95h
5
Further pairs of „ X ” - „ Y ” coordinates of points no. 2 ÷ 19 of the
user defined characteristic
96h 5 Yes -999 ÷ 1999
The value of „ X ” coordinate of point no. 20 of the user defined
characteristic, expressed in 0.1%
97h 5 Yes -999 ÷ 9999
The value of „ Y ” coordinate of point no. 20 of the user defined
characteristic, no decimal point included
A0h 1 Yes 0 ÷ 3
“ Omod ” parameter in “ OUtP ” menu (current output mode)
0 - current output disabled ; 1 - current output enabled with 4 ÷ 20mA
mode; 2 - current output enabled with 0÷20mA mode ;
3 - current output controlled via RS-485 interface
A1h 1 Yes -999 ÷ 9999 “ OUtL ” parameter in “ OUtP ” menu, no decimal point included
A2h 1 Yes -999 ÷ 9999 “ OUtH ” parameter in “ OUtP ” menu, no decimal point included
A3h 1 Yes 0 ÷ 999 “ Lo r ” parameter in “ OUtP ” menu, expressed in 0.1%
A4h
1
Yes 0 ÷ 199 “ Hi r ” parameter in “ OUtP ” menu, expressed in 0.1%
51