Sime Open Hybrid MEM 25-006 Installation And Maintenance Manual Download Page 41

Page: 41 / 60

3.5.6 DHW

PARAMETERS MENU

GENERAL SETTINGS

GENERATION

I/O CONFIGURATION

HEATING

COOLING

DOMESTIC HOT WATER



ENERGY SETTINGS

Press

to access domestic hot water.

Comfort Setpoint Temperature for DHW

DOMESTIC HOT WATER

S600

COMFORT

SETPOINT TEMPERATURE

FOR DHW:

55.0ºc

PAR.

DESCRIPTION

RANGE

6000

COMFORT Setpoint Temperature for DHW

[°C]

10.0 - 80.0

The DHW COMFORT temperature can be set manually (it is the

same value which can be modified in the user menu).

Reduced Setpoint Temperature for DHW

DOMESTIC HOT WATER

S602

REDUCED

SETPOINT TEMPERATURE

FOR DHW:

45.0ºc

PAR.

DESCRIPTION

RANGE

6010

REDUCED Setpoint Temperature for DHW

[°C]

10.0 - 80.0

The DHW REDUCED temperature can be set manually (it is

the same value which can be modified in the user menu).

Maintaining Storage Tank When In Reduced Mode

DOMESTIC HOT WATER

S606

MAINTAINING STORAGE

TANK IN REDUCED MODE:

DISABLED

PAR.

DESCRIPTION

RANGE

6060

Maintaining Storage Tank When In Re-

duced Mode

Disabled

Enabled

When in DHW REDUCED mode, it is possible to enable/disable

the heat pump from maintaining the storage tank at the calcu-

lated setpoint temperature.

DHW Anti-legionella Function

DOMESTIC HOT WATER

S611

ANTI-LEGIONELLA

FUNCTION

Activation : NOT ACTIVE

Day :

MONDAY

Start Time : 00:00

End Time

: 03:00

Setpoint :

55.0ºc

PAR.

DESCRIPTION

RANGE

6120

DHW Anti-Legionella Function

Enabled

OFF

6122

Anti-Legionella Function Start Day

1 - Mon ÷ 7 – Sun

6123

Anti-Legionella Function Start Time

00 - 23

6125

Anti-Legionella Function Stop Time

00 - 23

6127

Anti-Legionella DHW Temperature

Setpoint

10.0 - 80.0

Settings relating to the anti-legionella function: Activation,

Day of the week, Start time, End time, Setpoint.

This function requires the Heat Pump to prepare the storage

tank on the basis of the parameters set here but only if in the

previous 7 days, the temperature has not reached the anti-le-

gionella setpoint value.

DHW Storage Tank Dynamic Setpoint

DOMESTIC HOT WATER

S615

DHW STORAGE TANK

DYNAMIC SETPOINT:

ENABLED

PAR.

DESCRIPTION

RANGE

6150

DHW Storage Tank Dynamic Setpoint

Disabled

Enabled

If the DHW STORAGE TANK DYNAMIC SETPOINT , is activated,

it allows the DHW storage tank to be maintained by the Heat

Pump up to the heat pump convenience temperature (not ex-

ceeding the DHW setpoint) rather than the fixed nominal set-

point.

Summary of Contents for Open Hybrid MEM 25-006





























































Search results

Summary of Contents for Open Hybrid MEM 25-006

Reviews:

Sime Open Hybrid MEM 25-006, Installation And Maintenance Manual, Page: 41 / 60

Search results

Summary of Contents for Open Hybrid MEM 25-006

Reviews: