Sime Murelle Pro 25 LPG Use, Installation & Servicing Instructions Download Page 10

10

1.7 

fault / malfunction codes

if a fault/malfunction is detected during boiler operation, the 

message “al” will appear on the display followed by the fault 

code (eg. “06” - no flame detected).

if the message “reset” also appears, press and hold the 

button 

o

  

R

 for more than 3 seconds and check that the 

normal operating condition is restored.

if this operation is not successful, only one more attempt 

can be made, therefore:

–  close the gas cock

–  isolate the power supply

–  contact the Qualified technical Personnel.

caUtion

the table with the fault codes and the corresponding 

description is provided in the specific section of the 

iNstallatioN aND seRViCiNG iNstRUCtioNs.

2  shUtdown

2.1 

temporary shutdown

to temporarily interupt the boiler operation press and hold the 

button 

s

 for at least one second, once if in "WiNteR mode" 

n

 or twice if in "sUMMeR mode" 

l

“- -” will appear on the 

display the boiler will be in staND-BY. the boiler anti freeze 

function will be enabled.

danger

the boiler will still be powered.

caUtion

if the outside temperature might fall below ZeRo, 

since the appliance is equipped with an "antifreeze 

function"
–  oNlY PUt tHe BoileR iNto staND-BY
–  leave the main system switch set to "oN" (boiler 

is powered)

–  leave the gas cock open.

2.2 

shutting down for long periods

if the boiler is to be left unused for a long period, the following 

operations need to be carried out:

–  press and hold the button 

s

 for at least 1 second, once if in 

"WiNteR mode" 

n

 or twice if in "sUMMeR mode" 

l

 to 

put the boiler into stand-by “- -” will appear on the display

–  isolate the power supply

–  isolate the gas cock

–  close the heating and domestic hot water isolation valves

–  drain the heating and domestic hot water system if there is 

the risk of freezing.

caUtion

special attention should be made to installations 

in caravans, mobile homes and park homes. the 

domestic hot and cold water pipe work should be 

cleared of water. Heating systems not filled with a 

correct dilution of anti freeze, must be drained.

the "boiler anti freeze function" should not be 

considered as suitable alternative for correct 

 

"wintering". Contact suitably qualified personnel for 

further advice.

3  maintenance

3.1 

servicing

as a condition of the warranty and to ensure correct operation 

and efficiency, it is important that the boiler is serviced every 

12 months, within 30 days of the anniversary of the installation 

date ensure the required information is recorded in the Gas 

Boiler system Commissioning Checklist (Benchmark).

caUtion

Maintenance interventions must oNlY be carried out 

by professionally qualified personnel who will follow 

the indications provided in the iNstallatioN aND 

MaiNteNaNCe MaNUal.

3.2 

external cleaning

3.2.1  cleaning the case

When cleaning the cladding, use a cloth dampened with soap 

and water or alcohol for stubborn marks.

do not

Do not use abrasive products.

4  disposal

4.1 

disposal of the equipment (european 

directive 2002/96/ce

once it reaches the end of its operating life, the equipment 

MUst Be ReCYCleD in line with current legislation.

it MUst Not be disposed of together with urban waste.

it can be handed over to recycling centres, if there are any, or 

to retailers that offer this service.

Recycling prevents potential damage to the environment and 

health. it allows to recover a number of recyclable materials, 

with considerable savings in terms of money and energy.

Summary of Contents for Murelle Pro 25 LPG

















































Reviews: