background image

59

EN

SAFETY WARNINGS AND REGULATIONS

WARNINGS

–  After having removed the packaging make sure that 

the product supplied is integral and complete in all 

its parts. If this is not the case, please contact the 

Dealer who sold the appliance.

–  The  appliance  must  be  used  as  intended  by 

Sime

 

who  is  not  responsible  for  any  damage  caused  to 

persons,  animals  or  things,  improper  installation, 

adjustment, maintenance and improper use of the 

appliance.

–  In the event of water leaks, disconnect the appliance 

from  the  mains  power  supply,  close  the  water 

mains and promptly inform professionally qualified 

personnel.

–  Periodically  check  that  the  operating  pressure  of 

the water heating system when cold is 

1-1.2 bar

. If 

this is not the case, increase the pressure or contact 

professionally qualified personnel.

–  If the appliance is not used for a long period of time, 

at  least  one  of  the  following  operations  must  be 

carried out:

set the main system switch to "OFF";

close  the  gas  and  water  valves  for  the  water 

heating system.

–  In  order  to  ensure  optimal  appliance  operations 

Sime

  recommends  that  maintenance  and  checks 

are carried out 

ONCE A YEAR

.

WARNINGS

– 

It is recommended that all operators 

 read this manual 

carefully in order to use the appliance in a safe and 

rational manner.

– 

This manual

 is an integral part of the appliance. It 

must  therefore  be  kept  for  future  reference  and 

must always accompany the appliance in the event 

the  appliance  is  transferred  or  sold  to  another 

Owner or User or is installed on another system.

– 

Installation  and  maintenance

  of  this  appliance 

must  be  carried  out  by  a  qualified  company  or  by 

a professionally qualified technician in accordance 

with the instructions contained in the manual. The 

company or technician will, at the end of installation 

operations,  issue  a  statement  of  compliance 

with  national  and  local  Technical  Standards  and 

Legislation in force

RESTRICTIONS

IT IS FORBIDDEN

–  The  appliance  is  not  to  be  used  by  children  or 

unassisted disabled persons.

–  Do not use electrical devices or appliances such as 

switches, electrical appliances etc if you can smell 

fuel.  If this should happen:

open the doors and windows to air the room;

close the gas isolation device;

promptly call for professional assistance.

–  Do not touch the appliance with bare feet or with any 

wet part of the body.

–  Do  not  carry  out  any  technical  intervention  or 

cleaning operation before having disconnected the 

appliance from the mains power by setting the main 

switch to "OFF", and closing the gas supply.

–  Do  not  modify  the  safety  or  adjustment  devices 

without  authorization  and  instructions  from  the 

manufacturer.

–  Do not block the condensate drain (if present).
–  Do  not  pull,  detach  or  twist  the  electrical  cables 

coming out of the appliance even if the appliance is 

disconnected from the mains power supply.

–  Do  not  expose  the  boiler  to  atmospheric  agents. 

These  boilers  can  also  be  installed  in  partially 

covered areas, as per EN 15502, with a maximum 

ambient  temperature  of  60°C  and  a  minimum 

ambient temperature of - 5°C. It is recommended 

that the boiler is installed below weathered roofs, 

on the balcony or in a protected niche, to protect it 

from exposure to weathering agents (rain, hail and 

snow). The boiler is equipped as standard with an 

antifreeze function.

–  Do  not  block  or  reduce  the  size  of  the  ventilation 

openings  of  the  room  where  the  appliance  is 

installed, if present.

–  Remove the mains power and gas supply from the 

appliance  if  the  external  temperature  could  fall 

below ZERO (risk of freezing).

–  Do not leave  containers with flammable substances 

in the room where the appliance is installed.

–  Do  not  leave  packaging  material  around  since  it 

could  be  dangerous.  Therefore  dispose  of  it  as 

prescribed by legislation in force.

Summary of Contents for Brava One 25 OF ErP






























Reviews: