Silverline 125554 Instruction Manual Download

Page: 7 / 40

www.silverlinetools.com

Pendulum Jigsaw 560W

125554

Before Use

Fitting a blade

• Always check that a suitable blade is selected for the job that is to be

done (refer to the blade manufacturers information before use)

• Only fit blades that are in perfect condition. Blunt, bent and cracked

blades should be discarded

• Invert the jigsaw, remove the guard and loosen the Blade Locking Bolts

(9)

• Position the blade between the two locking bolts, so that the blade rests

against the guide roller

Note:

ALWAYS apply a lubricant between the blade and the roller, if you plan

on cutting metal or other hard materials.
•  Tighten the Blade Locking Bolts (9) and replace the guard
•  Ensure that the blade is fully secure before use
•  To remove the blade, remove the guard and loosen the blade locking

bolts then withdraw the blade from the underside of the saw

Connecting the dust extraction system

• This jigsaw is equipped with a Dust Extraction Port (4). Connecting the

tool to a vacuum cleaner or workshop dust extraction system is the
preferred method of dust extraction

• If vacuum dust extraction is unavailable, you must fit a generic dust bag

(not included)

WARNING:

Take special care when cutting some woods (such as beech,

oak, mahogany and teak), as the dust produced is toxic and can cause
extreme reactions. Always wear appropriate respiratory protection.

WARNING:

DO NOT use a dust bag when cutting metal. Hot metal particles

and sparks could ignite residual wood dust, or cause the bag to catch fire.
Always connect the jigsaw to a workshop dust extraction system when
cutting metal. Always clean the tool THOROUGHLY when switching from
cutting wood to cutting metal, and vice versa.

Setting pendulum action

• This jigsaw features a pendulum cutting function. Pendulum action

enables more efficient cutting
1. For fast cutting and thick material, set the Pendulum Action Selector

(6) to a high number

2. For fine cutting and thin material, set the Pendulum Action Selector (6)

to a low number

Note:

Practice using different pendulum settings to achieve the best finish

for your material.

Setting bevel angle

• This jigsaw is equipped with a tilting Shoe (5). This allows bevel cuts to

be made up to 45° to the left or right hand side
1. To alter the angle of the shoe, invert the jigsaw and loosen the Bevel

Locking Screws (11). The shoe is now free to pivot

2. Adjust the shoe to the required angle and then tighten the Bevel

Locking Screws

Note:

Ensure that the shoe is secured firmly in position prior to use.

Setting cutting speed

• To alter the cutting speed, rotate the Speed Control Dial (1). A high

number indicates a high cutting speed

•  Always set the machine speed to suit the material being cut
•  For soft materials use a high cutting speed
•  For hard materials use a low cutting speed. If cutting metal, use a

suitable coolant/cutting fluid

Operation

WARNING:

Always wear eye protection, an adequate dust mask, hearing

protection and suitable gloves, when working with this tool.

Note:

Before you use your jigsaw, it is recommended that you practice

on scrap material. The settings of the machine are crucial to achieving a
good quality finish, and your work could easily be damaged by using an
incorrect setting.

Handling your jigsaw

• Ensure that work will not move whilst being cut. Use clamps where

appropriate

• Always ensure that the On/Off Trigger Switch (2) and Lock-On Button (3)

are NOT engaged before connecting the saw to the power supply

• Always hold the jigsaw securely using the handle provided. Keep hands

well away from all moving parts

• For some tasks it may be preferable to lock the machine in the 'on'

position. To do this, squeeze the On/Off Trigger Switch (2) and depress
the Lock-On Button (3). The machine will now continue to run until the
trigger switch is squeezed and released

WARNING:

Allow the motor and blade to come to a complete stop before

placing the machine down. Always unplug the machine if it is to be left
unattended.

Making a cut

Note:

Always wear appropriate safety equipment. Use of this tool requires

eye protection, gloves, ear defenders, and good quality respiratory
protection.

1. Hold the jigsaw securely and rest the front edge of the Shoe (5) on the

edge of the workpiece

2. If starting a cut away from the edge of the workpiece, drill a pilot hole

large enough for the blade to pass through, where you wish to start
the cut

3. Check that the blade is not in contact with the workpiece, or any other

object

4. Start the machine by pressing the On/Off Trigger Switch (2)
5. Allow the motor to reach full speed, and smoothly push the jigsaw

forwards across the workpiece

6. Maintain a steady movement, and ensure that the Shoe (5) is kept

pressed against the work. Ensure that the power lead is kept well
away from the front of the saw as the cut is made

7. Allow the blade to pass through the material, then release the

trigger switch. Alternatively, if the cut does not reach the edge of the
workpiece, release the trigger switch and allow the blade to stop
moving before lifting out of the cut

8. Do not place the machine down until the motor and blade have

completely stopped

Using the parallel guide fence

• When working parallel to an edge, use the Parallel Guide Fence (10)
• The guide fence locates in the front of the Shoe (5) and is secured by

tightening the Guide Locking Screws (8)

• To follow an edge, simply make a cut, whilst keeping the vertical foot of

the guide fence pressed against the edge to be followed

Metal cutting

• Always use a suitable coolant/cutting oil when cutting metal. Failure to do

so will cause significant blade wear

• A continuous line of grease can be applied to the underneath of the

workpiece, instead of applying a a coolant from above