- 19 -
4.
The memory can accommodate 150 button commands.
If the memory is full the LCD display
q
shows "LEARN
FULL" and the learn mode will end.
5.
With the EXIT button
y
you return to the previous status
(except with a notice of "LEARN KEY" and/or "LEARN-
ING").
Code learn function
1.
Press the device button
e
for the device that the URC
should learn a button code.
2.
Hold down the S button
r
for a little longer than 3 sec-
onds. The notice "CODE SETUP" appears.
3. With the
or
button
t
select the menu "LEARN
SETUP" and then press the OK button
l
.
4.
In the LCD display
q
"LEARN SET" appears. Then press
the OK button
l
.
In the LCD display
q
"LEARN KEY" ap-
pears.
5.
First press the button on the URC that is to be taught. In the
LCD display
q
"LEARNING" appears. The URC now waits
for the infrared signal from the original remote control.
Note:
Should the notice not change to "LEARNING" you have
selected a button for which no button code can be
taught.
6.
Point the infrared sensors
2)
of both remote controls
towards each other.
7.
Now hold down the desired button of the original
remote control until "SUCCESS" or "LEARN ERROR"
appears in the display
q
of the URC.
8.
If in the LCD display
q
"SUCCESS" appears (process
successful), you can teach further buttons begining with
step 5. If "LEARN ERROR" appears (process unsuccessful)
repeat the process in any case from step 5.
9.
To stop the learning process press, during the display
“LEARN SET”, repeatedly the EXIT button
y
until the
standard display is show in the LCD display
q
. During
the notice "LEARN KEY" and/or "LEARNING" simply al-
low 30 seconds to pass without any operation then the
device will end the menu.
Delete All programmed buttons
1.
Hold down the S button
r
for a little longer than 3 sec-
onds. The notice "CODE SETUP" appears.
2.
With the
or
button
t
select the menu "LEARN
SETUP" and then press the OK button
l
. In the LCD
display
q
"LEARN SET" appears.
3.
With the
or
button
t
select "LEARN CLEAR"
(taught delete) and confirm with the OK button
l
. In
the LCD display
q
"CONFIRM CLEAR" (confirm delete)
appears.
4.
Confirm with the OK button
l
.
In the LCD display
q
"SUCCESS" appears.
All programmed buttons are de-
leted.
Finally the menu will automatically end.
BDA_KH 2159 - DT-53628_en.indd 19
08.07.2010 18:06:19
Summary of Contents for KH 2159
