- 17 -
System reset
Via this function you can reset the URC to its factory default
settings. Thereby all settings made by you will be deleted.
1.
Hold down the S button
r
for a little longer than 3 sec-
onds. The notice "CODE SETUP" appears.
2.
With the
or
button
t
select "SYSTEM SETUP" and
confirm with the OK button
l
.
3.
With the
or
button
t
select "SYSTEM RESET" and
confirm with the OK button
l
.
4.
In the LCD display
q
now appears "CONFIRM RESET".
Confirm the reset with the OK button
l
.
Then the LCD
display
q
shows “SUCCESS RESET”. All settings are
now deleted and the menu is closed. Otherwise you can
exit the menu by pressing the EXIT button
y
. Then the set-
tings remain preserved.
Timer Setup
The URC offers 2 timer modes, sleep timer and event timer.
Sleep timer
1.
Press the device button
e
for the device that is to be con-
trolled (i.e. VCR).
2.
Hold down the S button
r
for a little longer than 3 sec-
onds. The notice "CODE SETUP" appears.
3.
Press the
or
button
t
until "TIMER SETUP" is
shown. Press the OK button
l
"TIMER SLEEP" appears in
the LCD display
q
.
Confirm the selection of this function
with the OK button
l
.
4.
Now, below to the right in the LCD display
q
blinks the
minutes for the remaining time of the selected device.
Set with the
or
button
t
the desired value from 1
to 99 minutes. Press the OK button
l
to confirm.
With
programmed sleep-timer the LCD display
q
shows “
z
z”
on the right next to the time.
5. Position the remote control in such a way that your infra-
red signal can reach the device to be switched off. After
expiration of the set time the remote control will switch the
device off.
6.
If you now press the S button
r
“SL” is shown in the dis-
play
q
below on the left.
Event timer
The remote control has 4 event timers available via which
you are allowed to send out specific series of button combi
-
nations at designated times.
1.
Hold down the S button
r
for a little longer than 3 sec-
onds. The notice "CODE SETUP" appears.
2.
With the
or
button
t
select "TIMER SETUP" and
confirm with the OK button
l
. "TIMER SLEEP" appears
in the LCD display
q
.
With the
or
button
t
select
the desired memory slot "TIMER SETUP 1" to "TIMER
SETUP 4" and confirm with the OK button
l
.
BDA_KH 2159 - DT-53628_en.indd 17
08.07.2010 18:06:19
Summary of Contents for KH 2159
