Page 1
Model:
Product Type:
Study, understand and follow all instructions provided with this
product. Read these instructions carefully before installing,
operating, servicing or repairing this tool. Keep these instructions
in a safe accessible place.
INTENDED USE OF THE TOOL
• Normal use of this product is likely to expose the user to
dust and/or microscopic particles containing chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm. Always wear
appropriate safety equipment and clothing when using this
product. Study, understand and follow all instructions
provided with this product. Failure to read and follow all
warnings and operating instructions may result in damages
and serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and Bystanders).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool or use of the tool with accessories
not designed for it could result in serious injury or death.
• Always select the correct accessories of the correct size
and design for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is in
secure position and will not move during repair.
WARNING
SS7KA
7 PIECE SENSOR & SENDING
UNIT SOCKET SET
PRODUCT INFORMATION:
Made in China to Matco specifications
The manufacturer warrants this product to the original user against defective material
or workmanship for a period of 1 year from the date of purchase.
The manufacturer reserves the right to determine whether the part or parts failed
because of defective material, workmanship or other causes. Failures caused by
accident, alteration or misuse are not covered by this warranty.
The manufacturer, at its discretion, will repair or replace products covered under this
warranty free of charge. Repairs or replacements of products covered under this
warranty are warranted for the remainder of the original warranty period.
The manufacturer or its authorized service representatives must perform all warranty
repairs. Any repair to the product by unauthorized service representatives voids this
warranty. The rights under this warranty are limited to the original user and may not be
transferred to subsequent owners.
This warranty is in lieu of all other warranties, expressed or implied, including
warranties of merchantability and fitness for a particular purpose. Some states do not
allow the exclusion or limitations of incidental or consequential damages, so the
above limitations may not apply to you.
1 YEAR LIMITED WARRANTY
NOT FOR USE WITH IMPACT TOOLS.
This set includes 3/8" and 1/2" drive sockets designed to remove
oxygen sensors, vacuum switches as well as other sensors and
sending units. Do not use this tool outside of the designed intent.
Never modify the tool for any other purpose or use.
WARNING
When unpacking, check the parts diagram and part number listing
on page 4 to make sure all parts are included. If any parts are
missing or damaged, please call your distributor immediately.
Unpacking
www.matcotools.com
www.matcotools.com
• Oil Pressure Sending Unit Socket 1/2" Drive x 1-3/16" (29mm) x 90mm
- Allows the removal of oil pressure sending units on late
1980 and mid 1990 GM vehicles.
- Designed to be used with 1/2" drive tool.
• Vacuum Switch Socket 3/8" Drive x 7/8" (22mm) x 90mm
- Designed to remove and install vacuum switches with a 7/8" hex
and some oxygen sensors.
- Designed to be used with 3/8" drive tool or with a 1" wrench.
• Injector Socket 1/2" Drive x 1-1/16" (27mm) x 80mm
- Allows the removal and installation of thermal sensor switch on
1973 - 1977 GM vehicles.
- Designed to be used with 1/2" drive tool.
• Oxygen Switch Socket 3/8" Drive x 7/8" (22mm) x 80mm
- Designed to remove and install oxygen sensors in most domestic
and many imported vehicles.
- Socket designed with slot which allows clearance of wire.
- Designed to be used with a 3/8" drive tool or 1" wrench.
• Oil Pressure Sending Unit Socket 3/8" Drive 1" & 1-1/16" (27mm) x 76mm
- Includes a 1" and 1-1/16" hex which allows the removal of
oil pressure sending units.
- Special deep design fits switches up to 2-5/8".
- Designed to be used with a 3/8" drive tool or 1-1/8" wrench.
• Heated Oxygen Sensor Socket 1/2" Drive x 7/8" (22mm) x 50mm
- Socket designed with slot which accommodates the
connectors on heat oxygen sensors.
- Socket has a double 1/2" drive for easy access.
• Low Profile Offset Oxygen Sensor Socket 3/8" Drive x 7/8" (22mm) x 30mm
- Low profile design for use in tight spaces.
- Designed to be used with 3/8" drive tool.
1512201-14MA
English
