manualshive.com logo in svg

Silicon Laboratories Si5397 Series, User Manual

Share
Download
Silicon Laboratories Si5397 Series User Manual Download Page 25

11.  Writing a New Frequency Plan or Device Configuration to Non-Volatile Memory (OTP)

Note: 

Writing to the device non-volatile memory (OTP is 

NOT

 the same as writing a configuration into the Si5397 using Clock- Builder-

PRo on the Si5397-A-EB. Writing a configuration into the EVB from ClockBuilderPro is done using Si5397 RAM space and can be done
a virtually unlimited numbers of times. Writing to OTP is limited as described below.
 

Refer to the Si534x/8x Family Reference Manuals and device data sheets for information on how to write a configuration to the EVB
DUT’s  non-volatile  memory  (OTP).  The  OTP  can  be  programmed  a  maximum  of 

two

  times  only.  Care  must  be  taken  to  ensure  the

desired configuration is valid when choosing to write to OTP.

UG353: Si5397 Evaluation Board User's Guide

Writing a New Frequency Plan or Device Configuration to Non-Volatile Memory (OTP)

silabs.com

 | Building a more connected world.

Rev. 0.1  |  25

Summary of Contents for Si5397 Series





























Reviews:

No comments

Brands by name

Popular brands

Load more brands