1-6
14
Adjusting the convergence (CONV)
The CONV settings allow you to adjust the quality of the picture
by controlling the convergence. The convergence refers to the
alignment of the red, green, and blue color signals.
If you see red or blue shadows around letters or lines, adjust the
convergence.
These settings are stored in memory for all input signals.
1 Press the joystick.
The main MENU appears on the screen.
2 Move the joystick to highlight
CONV and press
the joystick again.
The CONVERGENCE menu appears on the screen.
3 First move the joystick up or down to select the
desired adjustment item. Then move the joystick left
or right to make the adjustment.
Additional settings (OPTION)
You can manually degauss (demagnetize) the monitor, change the
menu position, and lock the controls.
1 Press the joystick.
The main MENU appears on the screen.
2 Move the joystick to highlight
OPTION and press
the joystick again.
The OPTION menu appears on the screen.
3 Move the joystick up or down to select the desired
adjustment item.
Adjust the selected item according to the following
instructions.
x
x
x
x
Degaussing the screen
The monitor is automatically demagnetized (degaussed) when the
power is turned on.
To manually degauss the monitor, first move the
joystick up or down to select
(DEGAUSS). Then
move the joystick to the right.
The screen is degaussed for about 3 seconds. If a second degauss
cycle is needed, allow a minimum interval of 20 minutes for the
best result.
x
x
x
x
Changing the menuís position
Change the menuís position if it is blocking an image on the
screen.
To change the menuís on-screen position, first move
the joystick up or down to select
(OSD H POSITION)
for horizontal adjustment, or
(OSD V POSITION) for
vertical adjustment. Then move the joystick left or right
to shift the on-screen menu.
x
x
x
x
Locking the controls
To protect adjustment data by locking the controls, first
move the joystick up or down to select
(CONTROL
LOCK). Then move the joystick to the right, to select
ON.
Only the
!
(power) switch, EXIT, and
(CONTROL LOCK)
of the
OPTION menu will operate. If any other items are
selected, the
mark appears on the screen.
To cancel the control lock
Repeat the procedure above and set
(CONTROL LOCK) to OFF.
Select
To
horizontally shift red or blue shadows
vertically shift red or blue shadows
TOP
V CONVER TOP
vertically shift red or blue shadows at
the top of the screen
BOT
V CONVER
BOTTOM
vertically shift red or blue shadows at
the bottom of the screen
15
GB
Resetting the adjustments
This monitor has the following three reset methods. Use the
RESET button to reset the adjustments.
x
x
x
x
Resetting a single adjustment item
Use the joystick to select the adjustment item you want to reset,
and press the RESET button.
x
x
x
x
Resetting all of the adjustment data for the
current input signal
Press the RESET button when no menu is displayed on the screen.
Note that the following items are not reset by this method:
ï on-screen menu language (page 8)
ï adjustment mode in the COLOR menu (EASY, EXPERT,
sRGB) (page 11)
ï on-screen menu position (page 14)
ï control lock (page 14)
x
x
x
x
Resetting all of the adjustment data for all
input signals
Press and hold the RESET button for more than 2 seconds.
Note
The RESET button does not function when
(CONTROL LOCK) is
set to ON.
Technical Features
Power saving function
This monitor meets the power-saving guidelines set by VESA,
ENERGY STAR, and NUTEK. If the monitor is connected to a
computer or video graphics board that is DPMS (Display Power
Management Signaling) compliant, the monitor will automatically
reduce power consumption in three stages as shown below.
*
Figures reflect power consumption when no USB compatible
peripherals are connected to the monitor.
** ì Sleepî and ì deep sleepî are power saving modes defined by the
Environmental Protection Agency.
*** When your computer enters power saving mode, the input signal is
cut and NO INPUT SIGNAL appears on the screen before the
monitor enters active off mode. After a few seconds, the monitor
enters power saving mode.
RESET
Power mode
Power
consumption
*
!
(power)
indicator
normal
operation
≤
170 W
green
1 standby
≤
15 W
green and orange
alternate
2 suspend
(sleep)**
≤
15 W
green and orange
alternate
3 active off***
(deep sleep)**
≤
1 W
orange
power off
0 W
off
