background image

SGI™ External DVD Drive Installation Guide

5

VCCI Notice (Japan Only)

Industry Canada Notice (Canada Only)

This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.

Cet appareil numérique német pas de perturbations radioélectriques dépassant les
normes applicables aux appareils numériques de Classe A préscrites dans le Règlement
sur les interferences radioélectriques établi par le Ministère des Communications du
Canada.

Radio and Television Interference

The equipment described in this guide generates and uses radio frequency energy. If it is
not installed and used in accordance with the instructions in this guide, it can cause radio
and television interference.

This equipment has been tested and complies with the limits for a Class A computing
device in accordance with the specifications in Part 15 of FCC rules. These specifications
are designed to provide reasonable protection against such interference in an industrial
or office installation. However, there is no guarantee that the interference will not occur
in a particular installation. This system is not certified for home use.

You can determine whether your system is causing interference by turning it off. If the
interference stops, it was probably caused by the workstation or one of the peripherals.
To tell if the interference is caused by one of the peripherals, try disconnecting one
peripheral at a time to see if the interference stops. If it does, that peripheral is the cause
of the interference.

If your workstation does cause interference to radio or television reception, try to correct
the interference by following one or more of these suggestions:

Turn the television or radio antenna until the interference stops.

Summary of Contents for External DVD Drive









Reviews: