manualshive.com logo in svg

SILENT KNIGHT 5895XL, Installation And Operation Manual

Share
Download
SILENT KNIGHT 5895XL Installation And Operation Manual Download Page 35

151142

A-1

Appendix A
Compatible Devices

A.1

Notification Appliances

For proper operation, you must use polarized devices with a Model 7628 4.7k ohm EOL resistor on 
each loop. All supervised notification appliances used with the 5895XL must be polarized.

Note: Not all devices can use the Sync feature, be sure to check Table A-1 to ensure the device you 

have chosen will work with this feature. This control is UL listed for panel wide Synchronization.

A.1 below lists notification appliances compatible with the fire alarm control panel. Appliances which 
can be synchronized indicate the type of sync available in the columns marked Audio and/or Visual

.

Table A-1: Compatible Notification Appliances

Manufacturer

Model

Audio

Visual

Type

AMSECO

SH24W-153075

x

x

Horn/Strobe

SAD24-153075

x

Strobe

SAD24-75110

x

Strobe

SL24W-75110

x

Strobe

SL24C-3075110

x

Strobe

SLB24-75

x

Strobe

RSD24-153075

x

Strobe

RSD24-75110

x

Strobe

SH24W-75110

x

x

Horn/Strobe

SH24W-3075110

x

x

Horn/Strobe

SHB24-75

x

x

Horn/Strobe

SCM24W-153075

x

Chimes/Strobe

SCM24W-75110

x

Chimes/Strobe

SCM24C-3075110

x

Chimes/Strobe

SCM24C-177

x

Chimes/Strobe

H24W

x

Horn

H24R

x

Horn

Summary of Contents for 5895XL























































Reviews:

No comments

Brands by name

Popular brands

Load more brands