manualshive.com logo in svg

SILENT KNIGHT 5128, Manual

Share
Download
SILENT KNIGHT 5128 Manual Download Page 30

30

16.2  Silent Knight FSK and 4+2 Formats

The Silent Knight FSK and 4+2 formats transmit a 4-digit account number and a 2-digit alarm code.  When an
event is reported in either of these two formats, the dialer transmits the two digits shown in the second column.
The 9000 can be programmed to print either the two digits or the English message shown in the third column of
Table 16.2-I.  If you are using the 9032 line card, FSK2 and BFSK are the only formats that will report in
English.

Table 16.2-I:  9000 Pringout for Silent Knight FSK and 4+2 Formats

5128/29

DIGITS

TRANSMITTED

9000 RECEIVER ENGLISH

LANGUAGE PRINTOUT

ALARM 1-4

**01-04

ALARM 01 - ALARM 04

ALARM RESTORE 1-4

**21-24

RESTORE 01 - RESTORE 04

TROUBLE 1-4

61-64

TROUBLE 01 - TROUBLE 04

TROUBLE RESTORE 1-4

71-74

AC TROUBLE

AC LOST

60

AC RESTORE

AC RESTORE

70

TEST

MANUAL TEST

30

TEST

AUTOMATIC TEST

30

TEST

FIRE DRILL

30

TEST

*DOWNLOADING SUCCEEDED

30

TEST

*DOWNLOADING FAILED

30

TEST

PHONE LINE #1 TROUBLE

31

PHONE LINE TROUBLE 01

PHONE LINE #2 TROUBLE

32

PHONE LINE TROUBLE 02

DATA LOST

39

DATA LOST

PHONE LINE #1 RESTORE

35

PHONE LINE RESTORE 01

PHONE LINE #2 RESTORE

36

PHONE LINE RESTORE 02

*Message not applicable.

**“02” and “22” will never be reported.  Channel/Zone 2 is a trouble indication only that will transmit

only “62” and “72.”

Summary of Contents for 5128




































Reviews:

No comments

Brands by name

Popular brands

Load more brands