background image

7

l

 Rear Electronics Section

CD Player

Portable Music Player

Metronome

To Power Outlet

Power Adaptor 

Jack

LINE OUT Jack (Monaural)

AUX IN Jack 

(Stereo Mini)

PHONES Jack 

(Stereo Mini)

Nomenclature

Control Panel

Battery Case

CAUTION

•  Before connecting the Silent Guitar to any external equipment, make sure the power is switched OFF 

or the volume is fully lowered on all devices. Failure to do so can result in a loud sound that can dam

-

age equipment or your hearing.

•  Never return the signal sent from Silent Guitar’s outputs directly, or via an external device to the AUX IN 

jack. Doing so can result in a feedback loop that may result in damaging the instrument’s electronics.

•  Never play at high volume for any extended period of time when using the inner earphones or head

-

phones. Doing so can permanently damage your hearing.

When connecting the instrument to external audio equipment, check the jack size and 

make sure to use a plug size that corresponds to the jack being used, and properly con

-

nect the cable to the jack.

Guitar Amp

Powered Speaker

Recording Equipment

Mixer, etc.

Stereo Inner Earphones

Stereo Headphones

*  Do not connect anything other 

than a pair of headphones 

or inner earphones to the 

PHONES jack. Doing so can 

cause failure.

*  Connecting/disconnecting a cable 

to the LINE OUT jack switches the 

power ON/OFF.

• Insert plug → power ON

• Disconnect plug → power OFF

Power Adaptor 

(sold separately)

Summary of Contents for SLG200N

















Reviews: