manualshive.com logo in svg

Silent Alert SA3000, Technical Manual

Share
Download
Silent Alert SA3000 Technical Manual Download Page 8

                                      SILENT ALERT SA3000 FIRE SAFE MANUAL             24/04/2015 

Designed & Manufactured by Clofield Limited 

Free technical helpline 01246 450789 www.silent-alert.co.uk 

SignWave 
 

1. 

Move keys A, B & 5 to the on position as shown. 

2. 

Switch SignWave on by moving the key labelled 

ON/OFF to the left.  
3. 

The Polling field strength will now be displayed using 

the SignWave front LED’s (telephone =  full power) . 
 
Once the range test is complete switch key 

B

 OFF.  

The fire key will flash every seven seconds to show the unit is 
in Fire Safe mode. If the unit is moved out of range or does 
not receive a polling signal within 5 minutes the SignWave 
will alarm to notify the user.  

 
 
 

 
Charging Base 
 

Plug the mains adaptor into a 13A socket and connect the jack plug to the  
SignWave base.  

 

Illustration shows the mains adapter (left) and optional 
Pillow Pad connected the charger using strain relief 
features.  

 
 
 
 
 
 
 
 
 
 

 
Place the SignWave onto the charging base to charge 
 

 

Summary of Contents for SA3000














Reviews:

No comments

Brands by name

Popular brands

Load more brands