6 of 12
ÐSIGNET
5600 Batch Controller
10.3 Auto Calibration Procedure
The auto calibrate procedure (sec. 10.2C) calculates a custom flow sensor/batch K-Factor based on volumetric measurement for more
precise batching. This process will compensate for installation abnormalities or nonstandard pipe sizes for maximum batch accuracy.
An accurate measurement reference container (e.g. known tank volume) is required for this procedure. If auto calibration is impractical
for your batch system, perform manual calibration using the K-Factors published in your flow sensor manual.
Requirements:
A. The flow sensor must be installed in the actual batch pipeline.
B. The flow control valve can be connected to the common (C)
and normally open (NO) batch contact terminals (sec. 4) or
the current output terminals (sec. 8B).
C. Either the batch contact or current output
MUST
be used to
energize and de-energize the main flow control valve which
starts and stops fluid flow into the known reference container.
D. Follow the steps outlined in the auto calibration procedure
(sec.10.2C) to obtain your batch system's custom K-Factor.
Batch K-Factor
1234.3
C.
Modify
K-Factor?
Auto Cal Volume:
XX.XXX Gallons
Batch K-Factor:
1234.5
B.
Accept
K-Factor?
Auto Calibrate:
<ENTER> to Stop
CALIBRATE: -- -- -- --
Enter Key Code
Press keys in sequence
to continue,
**** will appear during code entry.
Batch Units:
Gallons >
A.
B.
C.
Batch
Flow Timebase:
m >
Choose:
1
Change:
2
Save:
3
Set batch units:
Aa - Zz, 0 - 9,
/, _
Batch units
Set timebase:
S=seconds,
M=minutes,
H=Hours,
D=Days
Flow timebase
Auto Calibrate:
Batch K-Factor >
Auto Calibrate:
<ENTER> to Start
Auto Calibrate
Procedure
Accurate reference
container required.
See procedure
(sec. 10.3)
Start
Stop
ENTER
ENTER
ENTER
Save
S
ave
Enter volume
A.
Reenter
volume?
Batch Units:
Liter
Flow Time Base:
s S m M h H d D
ENTER
D.
Batch K-Factor:
60.000 >
Set batch
K-Factor:
0.0001 - 99999.
(see note*)
Batch K-Factor
G.
Last CAL: Sets user
defined date
Last calibration
E.
Set totalizer
units: Az - Zz,
0 - 9, /, _
(Label use only)
Totalizer units
Total Units:
Gallons x 1 >
Last CAL:
01-01-98
Total Units:
Liters X100
Last CAL:
01-01-98
Batch K-Factor:
3456.7
To return
to VIEW:
To restore original value:
quick
press
quick
press
To return
to VIEW:
To restore original value:
quick
press
quick
press
←
To step A
To step D
→
←
Back to step C
F.
Set totalizer
K-Factor:
0.0001 - 99999.
(see note*)
Totalizer K-Factor
Total K-Factor:
60.000 >
Total K-Factor:
3456.7
Overrun Volume:
XX.XXX Gallons
D.
Overrun comp.
Display shown only
when advanced mode
(sec.10.4E) and manual
overrun comp. (sec.10.4G)
is selected.
OR
Cancel
ENTER
ENTER
G
↓
ENTER
"SAVING"
briefly
displays
"SAVING"
briefly
displays
10.2 CALIBRATE Menu
(factory defaults shown in menu column 1)
*Note:
Batch and totalizer K-Factor settings represent the
number of pulses generated by the +GF+ SIGNET flow sensor for
each engineering unit of fluid measured (published in the flow
sensor manual).
WARNING!
The auto calibration procedure generates a custom batch K-Factor. The batch and Totalizer K-Factors are independent from
one another. ALWAYS reenter your totalizer K-Factor after performing the auto calibration procedure.
5600
Flow Sensor
Flow control valve
20
0
40
60
80
100
Batch contact terminals (sec. 4) OR
4-20 mA valve control terminals (sec. 8B)
Reference Container
EN TER
Batch %
Batch
Option
0
20
40
60
80
100
+GF+ SIGNET