background image

2

Wall-Mount Range Hood Installation Instructions

Use an extinguisher only if: you know you have a Class 

A

B

C

 extinguisher, you know how to operate the extinguisher, 

the fire is small and contained in the area where it started, the fire department is being called and you can fight the fire 

with your back to an exit.

TO REDUCE THE RISK OF INJURY IN THE EVENT OF A GAS LEAK

Extinguish any open flames.

Do not turn on the range hood fan, any type of ventilator or any appliances.

Open all doors and windows to disperse the gas. If the gas odor is still present, contact the gas company and fire 

department immediately.

Signature Hardware declines all responsibility in the event of failure to observe the instructions given here for 

 

installation, maintenance and suitable use of the product.

Signature Hardware further declines all responsibility for injury due to negligence and the warranty of the unit 

 

automatically expires due to improper maintenance.

Signature Hardware will not be held responsible for any damages to personal property or real estate or any bodily 

 

injuries whether caused directly or indirectly by the range hood.

VENTING REQUIREMENTS

The vent system must terminate to the outside via the roof or side wall. Never terminate the vent system to an attic or 

other enclosed area.

Do not use 4" laundry-type wall caps.

Use aluminum venting only.

Always keep the duct clean to ensure proper airflow.

Before installation, collect the following measurements:

1. 

Ceiling height 

2. 

Distance from floor to stove or counter top 

3.  Distance from stove or counter top to range hood

3. 

Height of hood and duct cover

FOR THE MOST EFFICIENT AND QUIET OPERATION

A distance of 28"-31" is recommended between the stove top and the bottom of the range hood. 

It is recommended that the range hood be vented vertically through the roof through 6" or larger round aluminum

venting.

Use no more than three 90° elbows. Make sure there is a minimum of 24" of straight vent between the elbows if more 

than one is used. Never install two elbows together.

Summary of Contents for WALL-MOUNT RANGE HOOD








Reviews: