background image

Installation & User Manual 

 

 

 

60dB, as a result, the isolation required between the subscriber and 

the donor antenna is in a range of 70dB.  The line of sight separation 

between the subscriber (indoor) and donor (outdoor) antennas 

represented by a free space loss of 70dB within a building is 17 

meters (55 feet).  The separation distance can be reduced if the donor 

antenna is mounted on the building exterior (i.e. on a roof), or using a 

directional donor antenna (narrow beam width).  For example, if a 

metal roof separates the indoor and outdoor antennas, the physical 

separation may be substantially reduced.  

 

The following table indicates separation distances for different 

installation configurations: 

 

 

Line of Sight in-

building  

Exterior Donor Antenna, 

with 20dB Attenuation

1

 

Exterior mounted 

Directional Antenna

2

 

Separation 

Distance 

meters (ft) 

17 (55) 

8 (26) 

4 (13) 

1

 

The attenuation is indicative of the construction material that a signal has to penetrate 

through

 

2

 As in 

1

, but using a directional antenna with a typical front to back ratio of 20dB 

 

It is not recommended that the donor (outdoor) and subscriber 

(indoor) antennas be installed within sight of each other.  Do not install 

the unit where a skylight or other low loss RF path exists between the 

donor or subscriber antenna.  Arrista recommends that the donor 

(outdoor) antenna be installed on the roof or on an outside wall of a 

building.  A cell phone can be used to determine if an adequate signal 

is present at the chosen location.  Run a length of 50-ohm cable 

between chosen location and the repeater unit.   

 

Cable Length  Recommended Cable 

< 50 ft 

Andrew CNT-100, CNT-200 

Times Microwave LMR-240, or equiv. 

50 – 100 ft 

Andrew CNT-400 

Times Microwave LMR-400, or equiv. 

> 150 ft 

Andrew CNT-600 or equivalent 

 

Select a suitable location for the subscriber (indoor) antenna, and 

connect it to the 

Ant 1

 port of the repeater. 

 

If only one subscriber (indoor) antenna is to be used, flip the switch to 

the left to disable the second subscriber port. 

Copyright © 2004 Arrista Technologies Inc.  All rights reserved. 

5

 

Summary of Contents for CR300













Reviews: