background image

 

 

8

 

SignalFire Telemetry 

Rev 2.0 

Remote Modbus Register Mapping 

 
In addition to forwarding messages for other devices, the Repeater also reports status registers to the 
SignalFire Telemetry Modbus Gateway. The data that is sent to the gateway is available at the gateway in 
registers where it can then be read by a Modbus RTU.  
 
This data is accessible at the same Slave ID that the Repeater is configured for 
 

Register Map 

Register 
Number 

Register 

Address 

(Offset) 

Description 

49988 

9987 or 65524  Major revision number for the mainboard 

49989 

9988 or 65525  Minor revision number for the mainboard 

49990 

9989 or 65526  Major revision number for the radio 

49991 

9990 or 65527  Minor revision number for the radio 

49992 

9991 or 65528  High 16 bits of SFTS node address 

49993 

9992 or 65529  Low 16 bits of SFTS node address (the radio ID) 

49994 

9993 or 65530  Slave ID readback 

49995 

9994 or 65531  Received signal strength of last packet from the slave 

49996 

9995 or 65532  Battery voltage of the Modbus client, in millivolts 

49997 

9996 or 65533  Minutes until this slave will time out, unless new data is received 

49998 

9997 or 65534  Number of registers cached for this slave device 

49999 

9998 or 65535  Remote device type which is 80 for the Repeater 

 
 
 
 

Technical Support and Contact Information 

SignalFire Telemetry 
140 Locke Dr, Suite B 
Marlborough, MA 01752 
(978) 212-2868 

[email protected]

 

 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for Repeater Series











Reviews: