manualshive.com logo in svg

SignalFire MBS-CBBL, Interface Manual

Share
Download
SignalFire MBS-CBBL Interface Manual Download Page 2

 

Rev 5.8 

SignalFire Telemetry 

 

2

 

Connections

 

 

The Modbus-in-a-Stick is supplied with a 6 conductor cable. The connections are as 
follows:

 

 

Wire Color 

Connection 

RED

 

Positive Power (6 to 36 VDC)

 

BLACK

 

Ground

 

GREEN

 

RS-485 “A”, 9600 Baud (default)

 

BROWN

 

RS-485 “B”, 9600 Baud (default)

 

ORANGE

 

RS-232 Debug/Programming TX, 9600 Baud

 

YELLOW

 

RS-232 Debug/Programming RX, 9600 Baud

 

 
 

When configured as a RS232 Modbus stick (base stamped “232”), Green = Stick RX, Brown = Stick TX. 
Ground must also be connected when using RS232 interface.

 

 
 

Status LED

 

The Modbus-in-a-Stick has one LED available for field diagnostics.

 

 

LED

 

Description

 

Slow Flash (3 second pause)

 

System is running and in communication with radio network

 

Fast Flash (0.5 second pause)

 

System is running but no network found

 

Solid On

 

System Fault, needs service

 

 

 

 

Summary of Contents for MBS-CBBL














Reviews:

No comments

Brands by name

Popular brands

Load more brands