Sig Marine 10400 Assembly Manual Download Page 7

5.

 

When the oxygen depletion pilot flame comes on, you must hold the knob in for 
10  to  20  seconds.    During  this  time  the  pilot  flame  heats  up  the  thermocouple.  
When the thermocouple is hot it generates a small amount of voltage, which will 
energize a small solenoid coil inside the gas valve. This energized coil permits the 
valve to regulate propane into the burner.  

 
6.

 

Adjust  the  burner  by  turning  counter-clockwise  to  Low.  To extinguish, turn the 
knob all the way clockwise to off. 

 

Caution:  This  heater  consumes  oxygen.    You  must  supply  sufficient  outside 
air to replace the oxygen used by the heater.  This unit is equipped with an 
oxygen depletion device which will turn off the pilot flame when the oxygen 
level  drops  to  95%  of  normal.    This,  in  turn,  cools  off  the  thermocouple, 
which shuts off the main valve. 

 

 
TROUBLESHOOTING

 

 

Gas Smell

 

 
1.

 

Extinguish  all  open  flames  and  smoking  materials,  close  both  manual  and  solenoid 
cylinder valves immediately.  Make sure that the appliance valve is closed. 

 
2.

 

Ventilate  all  interior  compartments  thoroughly.    Maintaining  as  much  ventilation  as 
possible,  open  cylinder  valves.    Make  sure  that  the  appliance  valve  is  still  closed.  
Apply a mixture of liquid detergent and water to all connections, checking for bubbles 
indicating a leak.  

Do not use a flame to check for leaks

.  

 
3.

 

When  repair  of  the  leak(s)  has  been  completed,  test  the  system  with  the  aid  of  the 
pressure gauge.   

 

Inadequate Heat - Flame Burning Low or Gas Out

 

 
1.

 

Your system may be low on fuel - check your tank pressure gauge. 

 
2.

 

The gas cylinder valve may not be fully open - make sure the handle is turned as far as 
it will go in the counter-clockwise direction. 

 
3.

 

The burner orifice may be obstructed.  Let the burner cool, then remove the 4 machine 
screws (2 each side) which secure the burner and valve assembly to the heater body.  
Remove  burner  assembly,  take  off  the  burner  cap,  and  remove  the  orifice  (you  will 
require a long 7mm or 9/32” socket or nut driver).  Clean out the orifice and reinstall 
the part. 

 

Summary of Contents for 10400











Reviews: