FEATURE OVERVIEW
●
2 Ohm Stable MOSFET Amplifier Design
●
Intercooled Semi-conductor Technology
●
Accurate Stated Amplifier Ratings
●
Gold/Silver Plated 4 Gauge Powwer and Ground Connections
●
Variable Bass Boost 0 - +18dB
●
Gold/Silver Plated Audio Input and Output Connections
●
Varable LP and HP Electronic X-OVER @ 12dB/octave
●
Efficient Heat Sink Transfer Technology
●
Regulted Amplifier Technology
●
Gold/Silver Plated RCA Output for multi-amp Installations
(1)(2) Line Input/Sub-Input
(5)(8)(10) "High-Pass" frequency control
This allows connection to any head unit that has a RCA outputs.
This control is active when the switch is set to "Hi-pass" and
permits selection of the desired crossover frequency.
(3) Input-selector switch
The sub outputs signal is a sum of the Ch1+2(Front) and ch3+4(Rear)
(6)(9)(12) CROSSOVER SELECTOR
outputs. All three inputs will accept signal for use with a head unit
Set the appropriate mode of operation. The 3 positions available
with three preamp outputs.
are FLAT, HIGH PASS and LOW PASS.
1) When set to "1+2Ch" position, the front Inputs (Ch1+2) will
provide signal for the entire Amplifier.
(13) POWER LED
2) When set to "1+2Ch, 3+4Ch" position, both the front and rear
When illuminated the amplifier is turned on.
inputs will accept signal allowing the use of head unit fader.
3) When set to "1+2Ch, 3+4Ch, SUB" all three inputs wil accept
(14) PROTECTION LED
signal seperately for use with a headunit with thre preamp outputs.
When illuminated it indicates a fault has occurred. Check installation.
(4)(7)(11) LEVEL
(15) GROUND
This allows level adjustment of the input signal. Use this control to
Connect directly to the vehicle's chassis.
correctly match the head unit to 3/4 volume, with the BASS and
NOTE : This is to be the first wire to hook up during installation
TREBLE on zero, then slowly turn up the amplifier level control towards
as damage could result.
the MAX end of the control, NOTE : If the sound becomes distorted,
turn this control down.
(16) +12V
(19) Loudspeaker connections
This must be connected directly th the vehicle batteries po)
(If the amplifier is to be connected in a bridged mode, proceed with
terminal via an inline fuse at the battery end.
the section "Bridged loudspeaker connections".) As with any audio
component, connection of the amplifier and speakers with the correct
(17) REMOTE
polarity is essential for goods bass reproduction. Ensure there fore
This terminal is for turning the amplifier on and off. This requires
when connection that the positive (+) loudspeaker terminal.
a requires a switched positive (+12V) to power "on" the amplifier,
The same applies to the negative (-) terminals. The left-hand amplifier
this can be found on the rear of the head unit in the form of a electric
channel must also be connected to the left-hand loudspeaker and the
antenna output, or a remote on output. Of not available you
right-hand the right-hand amplifier channel to the right-hand loudspeaker
can wire to the ACC position on the key.
Bridged loudspeaker connections
(18) FUSE
The AMP can also be bridge in a mono configuration. This enables you
Please ensure correct type of fuse is fitted, as specified in this manual. to use the amplifier for one or more subwoofer(s) or amid-range
speaker. In this configuration the amplifier sums the right-hand and
oeft-hand channels, delivering a single channel (mono) output.
Note : The amplifier can sum the right-and oeft-hand signal information
only both the right-and left-hand RCA connections have been made.
CAUTION : The amplifier must be presented with a load of 4 Ohms or higher in bridged mode. A lower load will cause the amplifier
to overheat or switch off. This can lead to permanent damage of the unit
FEATURE OVERVIEW
5 Channel Power Amplifier
TM500.5
