Sierra SR-24G -24 Owner'S Manual Download Page 6

6 to 17 

 

 

 

movable  appliances,  there  is  a  restraining  device  at  the  rear  of  the  unit.  If  disconnection  of  the  restraint  is 
necessary, reconnect the restraint after the appliance has been returned to its originally installed position. 
 

CLEANING 

DAILY: Clean top grate(s) with warm water, mild cleaner and wire brush. Clean and brush off debris from and 
around the burner area. Empty and clean grease pan. Griddle plates should be cleaned with warm water and 

scrubbed  with  cleaning  abrasive  such  as  a  griddle  brick  of  fine  grit  type.  Top  surface  can  also  be  ‘bleached’ 

with vinegar, pickle juice or club soda when the plate 

is warm to give the plate a ‘new’ look.

 

 
Remove the baking racks. Wash in hot soapy water and replace after the rest of the oven is cleaned. Remove 
the  oven  bottom  by  lifting  it  out  from  the  front  then  sliding  forward,  out  of  the  oven.  Scrape  off  any  food 
particles with a nylon griddle scraper. Be very careful about scratching the porcelain finish on the oven liner 
panels.  Wash  all  the  above  with  hot  soapy  water,  then  reassemble.  Baked  on  spills  may  be  loosened  and 
stubborn  stains  removed  with  ordinary  household  ammonia  and  scrubbing  with  a  nylon  pad  in  a  cold  oven 
only. Do  not  allow  spray  type  oven cleaners  to  come  into contact  with  the temperature  probe  in  the  oven. 
After cleaning the oven, rinse well with 1/4 cup of vinegar to one quart of clear water solution to neutralize 
any caustic residue of the cleaning compound. Wipe dry.  

PERIODIC:  Remove  open  burners  and  clean  with  warm  water  and  wire  brush.  Make  sure  the  ports  are  not 
clogged. Check valves and lubricate, if necessary. Consult your service agency or local Gas Company. 
 

STAINLESS STEEL PARTS 

 
Do  not  use  steel  wool,  abrasive  clothes,  cleansers  or  powders  to  clean  stainless  steel  surfaces.  All  stainless 
steel parts should be wiped regularly with hot soapy water during the day and a stainless steel liquid cleaner at 
the end of the day. To remove encrusted materials, soak in hot water to loosen the material, and then use a 
wood or nylon scraper. 
 
Contact the factory, factory representative or a local service company to perform maintenance and repairs. 
 

 

 

 

 

 

 

 

Summary of Contents for SR-24G -24


















Reviews: