Sierra Series 200, Owner'S Manual

Page: 103 / 121

103
Configuration Parameters
Timing Configuration
Parameter Name Description Addr
Default
Value
Type Set Value Get Value
dtmf_qual_delay
length of time dtmf tone must be detected by hardware to
be recognized
48 1 byte C106 48 B (0…255) D C107 48 D
telemetrydelayl
time from key up to start of key up telemetry
49 8 byte
C106 49 B (0…255) D C107 49 D
xmittimeouts_long time from key up to dropping carrier 50 40 byte C106 50 B (0…255) D C107 50 D
xmittimeouts_short time from key up to dropping carrier with link delay off 51 0 byte C106 51 B (0…255) D C107 51 D
dtmftimeouts
timeout between dtmf entry to abort command entry
52 30 byte
C106 52 B (0…255) D C107 52 D
busytimeouts dtmftimout for busy signal on case 53 60 byte C106 53 B (0…255) D C107 53 D
id_idleto
time before ID is forced after transmit starts after long
transmit gap (repeater port)
54 30 word C108 54 B (0…255) D C109 54 D
id_politeto
time remaining in absolute timeout when ID will be
triggered if transmit is idle (repeat port)
56 120 word C108 56 B (0…255) D C109 56 D
id_absto
absolute timeout for sending ID (normally 10 minutes)
58 600 word
C108 58 B (0…255) D C109 58 D
id_lnkidleto
time before ID is forced after transmit starts after long
transmit gap (link port)
60 5 word C108 60 B (0…255) D C109 60 D
cmdteldelays
delay after first command recognized until command
telemetry starts
62 15 byte C106 62 B (0…255) D C107 62 D
serteldelays
delay after first command recognized until command
telemetry starts, with rs232 command source and
teltolocal=1. Value is 1 (defined by SERTELDELAYS0) if
teltolocal=0.
63 1 byte C106 63 B (0…255) D C107 63 D
dialtonetimeout
timeout for dial tone after prefix recognized if not
command is entered
64 10 byte C106 64 B (0…255) D C107 64 D
parmtimeout
timeout while waiting for a command parameter to be
entered
65 5 byte C106 65 B (0…255) D C107 65 D
fantimeouts timeout for fans after transmit stops 66 255 byte C106 66 B (0…255) D C107 66 D
rcvqdelays_loc
time local receiver needs to detect COR and/or PL until
detected active, normal value
67 10 byte C106 67 B (0…255) D C107 67 D
rcvunqdelays_loc
local receiver delay to drop receiver active, normal value
68 30 byte C106 68 B (0…255) D C107 68 D
rcvqdelays_lnk
link receiver delay to receiver active detect, normal value
69 10 byte C106 69 B (0…255) D C107 69 D
rcvunqdelays_lnk
link receiver delay to drop receiver active, normal value
70 1 byte C106 70 B (0…255) D C107 70 D
rcvqdelays[]
specific radio values, set by set radio defaults
71 see above byte C106 71 B (0…255) D C107 71 D
rcvunqdelays[] specific radio values, set by set radio defaults 79 see above byte C106 79 B (0…255) D C107 79 D
Strings
Parameter Name Description Addr
Default
Value
Type Set Value Get Value
allocated size of prefix 5
prefix_string 0 terminated string with prefix (0..9, A..B, # allowed) 87 special
allocated size of ID string 20
id_string 0 terminated string to be sent as repeater ID 92 special
id_string2 0 terminated string with alternate ID 112 special
allocated size of location string 20
loc_string 0 terminated string with location 132 special
loc_string2
0 terminated string with alternate location
152 special
idselect OBSOLETE 172 0 byte C106 172 B (0…255) D C107 172 D