manualshive.com logo in svg

Sierra Wireless MP597, Quick Start Manual, Page: 5 / 13

Share
Download
Sierra Wireless MP597 Quick Start Manual Download Page 5

Rev 1.0  Mar.10

25

Installing MP 597

For installing the latest software version (.exe file), you can go to the Sierra 
Wireless website: http://www.sierrawireless.com/support. 

For the updater tool to execute, please install the USB drivers available on the 
website before executing the .exe file. 

Tip:

Copy the USB Serial Driver.inf file to your desktop. Then power up the MP597W and 

connect USB.  Install from specific location and point to this .inf file. For detailed instruc-
tions on installing the USB drivers, please refer to Universal Serial Bus Application Note.

1.

Connect the MP 597 to your computer using an Ethernet cable or a serial 
cable USB cable.

2.

Connect the power adapter and antennas to your MP 597.

a.

A Sierra Wireless firmware update welcome screen appears. Click on 
Next.

Note:

Figure 0-1

 is for illustration purposes. Your firmware version may vary.  

Figure 0-1: Launch Screen

b.

Choose the interface you want to program the modem through and click 
on Next.

d.

When the lights illuminate, your MP 597 has success-
fully completed OTASP and is registered on the 
Verizon network.

Summary of Contents for MP597














Reviews:

No comments