Siemens WT7W466SZA Installation And Operating Instructions Manual Download Page 55

Page: 55 / 64

Help with the appliance

Help with the appliance

Help with the appliance

Faults

Cause/remedy

The appliance will not

start.

Check the mains plug and the fuses.

Creasing.

■

Load exceeded or incorrect programme selected for a type of fabric. All the

required information can be found in the programme table.

Page 24

■

Remove laundry from the drum as soon as the drying programme has fin-

ished. Creasing occurs when clothing is left in the drum.

Water is leaking out.

■

The appliance may be positioned at an angle. Level the appliance.

■

In the base unit, make sure that:

– The heat exchanger cover is properly locked.

– There is no dirt or debris on the heat exchanger cover's seal.

Page 45

■

If the optional drain hose* is installed, make sure that the drain hose is cor-

rectly connected.

Page 40

Programme duration dis-

played changes as dry-

ing progresses.

Not a fault. The moisture sensor measures the residual moisture in the laundry

and adjusts the programme duration (with the exception of timed programmes).

Laundry is not dried

properly or is still too

damp.

■

After the programme has ended, warm laundry feels damper than it actu-

ally is. Spread out the laundry and let it cool down.

■

Adjust the drying time or increase the degree of dryness. This will extend

the drying time but the temperature will remain the same.

■

Select a timed programme to add extra drying time for laundry that is still

damp.

■

Select a timed programme for a small load.

■

Do not exceed the maximum load for a programme.

Page 24

■

Clean the moisture sensor in the drum. The sensor may become covered in

a fine layer of limescale or detergent and care product residue, which then

impairs its performance.

Page 44

■

Drying has been interrupted as a result of a power cut, because the conden-

sation container is full or because the maximum drying time has been

exceeded.

Note:

Summary of Contents for WT7W466SZA

































































Search results

Summary of Contents for WT7W466SZA

Reviews:

Related manuals for WT7W466SZA

Brands by name

Popular brands

Siemens WT7W466SZA, Installation And Operating Instructions Manual

Search results

Summary of Contents for WT7W466SZA

Reviews:

Related manuals for WT7W466SZA

Brands by name

Popular brands