GAMMA
instabus
Technical product information
February 2012
UP 258D11 OPTISENS OFFICE Presence detector / motion detector with lighting control
5WG1 258 2DB11
Technical manual
UP 258D11, 8 pages
Siemens AG
Infrastructure & Cities Sector, Building Technologies
Update: http://www.siemens.com/gamma
© Siemens AG 2012
Control Products and Systems
Subject to change without further notice
P.O. Box 10 09 53, D 93009 Regensburg
2.13.1.6/2
brightness fluctuations are filtered out. The measure
ment range of the internal light sensor is between 20
and 1000 lux.
The settings determine whether the brightness value
computed by the device or a brightness value received
from outside is used for the detector's remaining func
tional blocks.
Integrated light control (on – off)
If the brightness controller is enabled (automatic mode)
the lighting is switched on as soon as the brightness falls
below a set lower threshold. The lighting is switched off
if the set upper brightness threshold is exceeded. The
brightness thresholds are variable either via parameters
or via communication objects.
The controller can also be operated semi automatically
by separating into two individual switching objects for
exceeding or falling below the threshold. In this way, it
can be switched to “Only on” or “Only off.”
If the controller receives a switching or dimming com
mand via the associated communication object over
KNX/EIB, then this is deemed an external override and
the controller switches automatic mode off. This change
of status is sent simultaneously on the bus via the
“Automatic Status” object.
Operation via infrared (IR) remote control
The IR receiver integrated in the presence detector can
control light and shade, as well as store and call up
scenes via a special IR remote control.
The IR commands implemented can be combined via
communication objects with the other function blocks or
used to control other devices.
The IR decoder can be controlled only with one of the
Siemens IR remote controls shown in figure 1. The re
mote controls have a range of 5 meters maximum.
The IR decoder cannot distinguish between remote con
trols. The functionality of button pairs A to F (see dia
gram in figure 1) will be configured via the ETS.
Figure 1. IR remote control units for UP 258D11
Commissioning / Factory default settings
After the device is connected to the bus voltage, the
sensor must first "Restart". In this phase, the program
ming LED flashes double.(
¼sec. ON
¼sec. OFF
¼sec. ON
1¼sec. OFF
…
)
After "Restart" of the sensor, it appears that no motion is
detected at present, the programming LED is off.
Factory default settings
In the as delivered state, the parameter Operating Mode
is set to Setting Mode.
While the device is in "Setting Mode", the integrated
programming LED displays the PIR sensor state. (illumi
nates briefly with motion)
Note:
The programming LED can be recognized more easily
without the design cover!
If the device is in programming mode, the LED stays on
and does not flash. The PIR state is then not displayed.
Programming mode
Press the programming key short (< 0,5 s) to enable
programming mode. This is indicated by the program
ming LED.
Factory setting
When the programming key is pressed very long (> 20 s)
the device is reset to the default factory settings. This is
indicated by evenly flashing the programming LED. The
flashing stops after 5 seconds.
Behavior after programming
The behavior of the device after programming with the
ETS is dependent on the configuration. The description
of the features, parameters and objects is in the applica
tion program description of the device.
Note:
When the programming key is pressed longer (> 0,5 s to
2 s) no functions are activated.
When the programming key is pressed longer (> 2 s) the
device starts connection test. This is a special mode for
Desigo TRA. The device may be blocked for the manufac
turer specific functions for approx. 10 seconds for the
programming mode. This is indicated by briefly flashing
the programming LED.
