Siemens Synco living Operating Instructions Manual Download Page 85

Page: 85 / 100

85 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Radio plug adapter

23.08.2008

Radio plug adapter

Operation KRF960 (switching)

LED display functions:

•

LED lit:

Contact closed

•

LED off: Contact open.

Pressing the button can locally reverse the
contact state:

•

LED lit (contact closed) and press button

LED off (contact open)

•

LED off (contact open) and press button

LED lit (contact closed)

Operation KRF961 (dimming)

LED display functions:

•

LED lit:

Output active

•

LED off: Output off

Press the button to locally reverse the current
output state:

•

LED lit (output active) and press button

LED off (output off)

•

LED off (output off) and press button

LED lit (output 100%)

The local button does not allow for dimming
the output.

Summary of Contents for Synco living





































































































Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands

Siemens Synco living, Operating Instructions Manual

Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands