Siemens Synco living Operating Instructions Manual Download Page 53

Page: 53 / 100

53 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Stage setpoint for night cooling

Specify here the stage for the ventilation plant when night cooling is active.

Main menu > Ventilation > Night cooling > Stage setpoint:

Factory setting

Stage 1

Setting

Off

Stage 1

Stage 2

Stage 3

Precooling time max

Night cooling is released only during the set maximum precooling time
(0..2880 min). When the setting is 0 min, night cooling is disabled.

Main menu > Ventilation > Night cooling > Precool time max:

Factory setting

0 min

Setting

Ventilation settings

Holiday mode time

If the central apartment unit is in holiday mode (as per the settings in menu
Holidays / Special days), ventilation is reduced.

Ventilation uses the current apartment operating mode from the holiday pro-
gram and selects the required ventilation stage based on it.
This ventilation stage is operated daily at the set time (00:00..24:00) for the
specified duration.

Use this operating line to select the time to start ventilation while on holidays.

To start ventilation in holiday mode, the stage selection (page 45) must
be set to Auto.

Main menu > Ventilation > Ventilation settings > Holiday mode time:

Factory setting

10:00

Setting

Holiday mode period

Ventilation in holiday mode runs every day for the period set here
(00.00..06.00 hh.mm).

Main menu > Ventilation > Ventilation settings > Holiday mode period:

Factory setting

00.30 hh.mm.

Setting

Summary of Contents for Synco living





































































































Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands

Siemens Synco living, Operating Instructions Manual

Search results

Summary of Contents for Synco living

Reviews:

Related manuals for Synco living

Brands by name

Popular brands