Siemens Synco living Operating Instructions Manual Download Page 48 | Manualshive

Page: 48 / 100

background image

48 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Stage assignment for smoke

Specify the stage for ventilation when the central apartment unit detects
smoke.

Main menu > Ventilation > Stage setpoints > Smoke:

Factory setting

Off

Setting

Off

Stage 1

Stage 2

Stage 3

Stage assignment for ventilation contact

Specify the stage for ventilation when the ventilation contact is closed.

Main menu > Ventilation > Stage setpoints > Ventilation contact:

Factory setting

Off

Setting

Off

Stage 1

Stage 2

Stage 3

Ventilation time switch

Switching times

The central apartment unit controls the ventilation stages based on a ventila-
tion time switch for automatic ventilation operation mode (stage selection:
Auto).

Main menu > Ventilation> Ventilation time switch > …

Up to six switching points can be set for each weekday and one special day.
In addition, you can specify the ventilation operating mode (Comfort, Precom-
fort, Economy) the system should change over for each switching point.

The switching points can be created, deleted, changed, or copied to another
weekday. The setting is carried out based on the room time switch (see
page 37).

The factory setting contains the switching times for all weekdays at
06:00 (changeover to Comfort) and 22:00 (changeover to Economy).

«
...
46
47
48
49
50
...
»

Summary of Contents for Synco living





































































































Reviews:

No comments

Related manuals for Synco living

Brand: wattio Pages: 20

Brand: Dahua Pages: 58

Brand: hager Pages: 62

coviva Smartbox TKP100A

Brand: hager Pages: 45

Brand: Samson Pages: 8

Brand: Samson Pages: 60

Brand: Samson Pages: 40

Brand: Tamiya Pages: 5

Brand: Cypress Pages: 3

Brand: Funktel Pages: 28

IB-TRON 4000 SOL

Brand: INSBUD Pages: 14

Brand: Nautronic Pages: 6

Brand: Redbusbar Pages: 12

Ratio Feeder J+ Advanced Series

Brand: H.E. Anderson Pages: 11

Security Center AZ5140

Brand: Abus Pages: 16

Brand: Dannmar Pages: 85

ECL Comfort 300

Brand: Danfoss Pages: 75

Brand: sonitor Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands