Siemens SIWAREX WP251 Manual Download Page 106

Page: 106 / 220

Scale parameters and functions

8.17 DR 17 Control analogue output

SIWAREX WP251

106

Manual, 12/2015, A5E37203357A

8.16.2

Weight simulation specification

Only use weight simulation values which are within the measuring range of the scales. The

word "TEST" is displayed on the main display during simulation and a status bit is set. From

the start of simulation onward, all parameterized limits, inputs and outputs etc. refer to the

simulation weight.

8.17

DR 17 Control analogue output

8.17.1

Overview

If data record DR 17 is configured as the source for the analog output (see Analog output

source (Page 93)), specifying a control output sends a corresponding output current at the

analog output. The set value is not saved in non-volatile memory.

Procedure

●

In data record DR 7, check that "Control by DR17" has been configured as the source for

the analog output

●

Check the parameter assignment of the analog output

●

Enter a value in data record DR 17

●

Transfer the data record to the scales

Table 8- 17 Assignment of data record 17

Variable

Note

Type

Length

(bytes)

Default Min.

Max.

Modbus

registers

Data record

number

Contains no. of the data record

USHORT

1606

Length

Data record length information

USHORT

1607

Application

Information about which applica-

tion the data record belongs to

USHORT

105

1608

Version

identifier

Current data record version

information

USHORT

65635

1609

Analog out-

put specifica-

tion

(Page 106)

Value to be output/simulated

FLOAT

1610

8.17.2

Analog output specification

The set value must be within the range of the analog output scaling in DR 7: Start value for

the analog output (Page 93) < Set value < End value for the analog output (Page 93).

Summary of Contents for SIWAREX WP251





























































































































































































































Search results

Summary of Contents for SIWAREX WP251

Reviews:

Brands by name

Popular brands

Siemens SIWAREX WP251, Manual

Search results

Summary of Contents for SIWAREX WP251

Reviews:

Brands by name

Popular brands