Siemens SIWAREX WP251 Manual Download Page 93

Page: 93 / 220

Scale parameters and functions

8.8 DR 7 Process interfaces

SIWAREX WP251
Manual, 12/2015, A5E37203357A

8.8.7

Analog output range

This parameter is used to define the output current range.

Function code

Output current

0 … 20 mA

1 (default)

4 … 20 mA

8.8.8

Analog output source

The analog output can be used for a range of purposes. This parameter defines the tag that

controls the analog output.

Function code Basis for the analog output
0

Gross weight (rounded according to DR 3)

1 (default)

Net weight (rounded according to DR 3)

Tare weight (rounded according to DR 3)

Coarse/fine signal (specified percentage from DR 25)

Control using data record DR 17

Control using S7-I/O ("s_I_O_DATA.AQ_CONTROL")

8.8.9

Response of analog output to faults or SIMATIC STOP

This parameter defines the response of the analog output following a fault of the SIWAREX

module or SIMATIC STOP.

Function code

Response

0 (default)

Switch off

Retain function

Output configured substitute value (e.g. 3.5 mA)

Output maximum value (24 mA)

8.8.10

Start value for the analog output

This parameter defines the start value of the scaling of the analog output and thus

corresponds to 0 mA or 4 mA, depending on the setting. The value can be greater or less

than the end value.

8.8.11

End value for the analog output

This parameter defines the end value of the scaling of the analog output and thus

corresponds to 20 mA.

Summary of Contents for SIWAREX WP251





























































































































































































































Search results

Summary of Contents for SIWAREX WP251

Reviews:

Brands by name

Popular brands

Siemens SIWAREX WP251, Manual

Search results

Summary of Contents for SIWAREX WP251

Reviews:

Brands by name

Popular brands