Siemens SIWAREX WL200 Series Operating Instructions Manual Download Page 18

Page: 18 / 102

Installing

4.2 Procedure for mounting the device

SIWAREX WL200

Operating Instructions, 07/2016, A5E02199611B-03

NOTICE
Damage to load cells through incorrect mounting

•

Provide indented claws or crane eyebolts on the load bearer to ensure that hoisting gear

can be used safely.

•

Load cells must never be overloaded. Put the load carrier down slowly for this reason.

With load cells of smaller rated loads in particular, there is a risk of stretching the load

cell bodies when attaching force transfer devices, e.g. when tightening locknuts.

•

Adjust the existing overload protection to ensure that it can still reliably sense transfer of

the required load. The overload protection must permit a rise in weight unhindered until

the setpoint weight is reached.

•

Protect the gap between the load cell and overload protection from the build up of dirt or

ice.

•

The load must be introduced in the measuring direction of the load cell. Torsional and

bending moments, eccentric loads and lateral forces are disturbances. These

disturbances falsify the measured result and can damage the load cell if the permissible

limits of the load cell and mounting components are exceeded.
The mounting components normally allow so much room for movement that heat

expansion will not result in lateral loading.

NOTICE
Destruction of load cells
Proceed carefully with installation. The load cells can be destroyed if they are installed

incorrectly.

4.2

Procedure for mounting the device

Observe the installation guidelines for the mounting components.
–

You can find dimension drawings of installation elements under Dimension drawings

(Page 69).

–

Lay the cables for the load cells through cable glands in the form of a vertical

downwards loop to discourage the penetration of water.

Check that the load cells and mounting components are installed correctly, e.g. by

checking the mounting dimensions and oscillation distances.

Summary of Contents for SIWAREX WL200 Series







































































































Search results

Summary of Contents for SIWAREX WL200 Series

Reviews:

Brands by name

Popular brands

Siemens SIWAREX WL200 Series, Operating Instructions Manual

Search results

Summary of Contents for SIWAREX WL200 Series

Reviews:

Brands by name

Popular brands