manualshive.com logo in svg

Siemens SITRANS WW100, Operating Instructions Manual

Share
Download
Siemens SITRANS WW100 Operating Instructions Manual Download Page 17

5. Use  or 

 arrows to set the value to 3.

6. Press and hold 

 for 3 seconds to save.

You now have access to all of the parameter sets for both the Control Unit and Drive Unit.

4.2.1.4

Parameters

Note
In order to access or modify the parameter settings, P0003 must be set to EXPERT MODE 

(see P0003 - Expert mode (Page 16)).

P2000 - Maximum RPM

Sets the maximum motor RPM.
The factory default value of the Drive configuration RPM is 6000. At the factory, we have set this 

to a maximum of 2500

 as the weighfeeder should not exceed the corresponding belt speed of 

approximately 50 ft/min or 0.254 meters/second.
The application for which this weighfeeder will be used has been engineered by a software tool 

at Siemens. From the data provided, certain parameters are generated identifying the 

Design Rate, Design Speed, and Design Load. You are interested in the Design Speed: this will 

aid in setting the Maximum RPM – P2000.

Calculating P2000
Design Speed P14 refers to Parameter 14 of the Siemens integrator BW500. Please see the 

Technical Report supplied with the weighfeeder. 

Imperial:

 

 

P2000 = Design Speed (P14-BW500) * k Factor (47.28702)

 

Metric:

 

 

P2000 = Design Speed (P14-BW500) * k Factor (9308.468)

 

Here are a few examples with both metric and imperial application data.

Design Speed

k Factor

P2000

Design Speed

k Factor

P2000

ft/min.

imperial

CU310-2

m/sec.

metric

CU310-2

10

47.28702

472.870

0.05080

9308.458

472.870

22

47.28702

1040.31

0.11176

9308.458

1040.31

35

47.28702

1655.05

0.17780

9308.458

1655.05

50

47.28702

2364.351

0.25400

9308.458

2364.351

1. Set S120 display to drive number 02 (see Switching units (Page 16)).
2. Use   or   arrows to navigate to P2000. The value should read 2500 after the application 

software has been loaded.

3. Press 

 to access and view the current setting.

Installing

4.2 Electrical installation for servo driven models

SITRANS WW100

Operating Instructions, 06/2018, A5E33560618-AC

17

Summary of Contents for SITRANS WW100















































Reviews:

No comments

Brands by name

Popular brands

Load more brands