Siemens SITRANS I300 Operating Instructions Manual Download Page 38

Page: 38 / 44

Description

Specification

Residual ripple within voltage range

≤ 3.6 V

Current consumption of SITRANS I300 (DC 24 V)

≤ 210 mA

Power loss (1.5 W load)

3.3W @ DC 24 V in

Reverse polarity protection

Yes

Table 9-2

Power supply output

Description

Specification

Rated voltage (output)

15.6 V

Max. current (output)

459mA

Max. power (output)

1.5W

Table 9-3

Galvanic isolation (Test voltage according to EN 60079-11)

Description

Specification

EIA-485 to EIA-485-IS

AC 1500 V

Power supply to EIA-485-IS

AC 1500 V

9.4

Diagnostics

Table 9-4

Diagnostics

Description

Specification

Monitoring 24 V power supply

Green LED "PWR"

Bus monitoring

Yellow LED "RX/TX"

Technical data
9.4 Diagnostics

SITRANS I300 Isolating power supply with EIA-485 interface

Operating Instructions, 01/2019, A5E45099319-AA

Summary of Contents for SITRANS I300













































Search results

Summary of Contents for SITRANS I300

Reviews:

Related manuals for SITRANS I300

Brands by name

Popular brands

Siemens SITRANS I300, Operating Instructions Manual

Search results

Summary of Contents for SITRANS I300

Reviews:

Related manuals for SITRANS I300

Brands by name

Popular brands