Siemens SIMOTICS SD SH 71 315 Series Operating Instructions Manual Download Page 78

Page: 78 / 132

Commissioning

7.1 Measures before commissioning

1LE7 shaft heights 71 ... 315

Operating Instructions, 04/2022, A5E51689275A-AA

7.1.7

Further documents

Note
Further documents

Observe all of the other documents provided with this motor.

7.1.8

Setpoint values for monitoring the bearing temperature

Prior to commissioning

If the motor is equipped with bearing thermometers, set the temperature value for

disconnection on the monitoring equipment before the first motor run.

Table 7- 1

Set values for monitoring the bearing temperatures before commissioning

Set value

Temperature

Alarm

115 °C

Shutting down

120 °C

Normal operation

Determine the maximum operating temperature of the bearings T

operation

taking into account

the temperature, bearing load and influences of the plant on the motor in °C. Set the values

for shutdown and warning corresponding to the operating temperature T

Table 7- 2

Set values for monitoring the bearing temperatures

Set value

Temperature

Alarm

operation

+ 5

K ≤

115 °C

Shutting down

operation

+ 10

K ≤

120 °C

Summary of Contents for SIMOTICS SD SH 71 315 Series





































































































































Search results

Summary of Contents for SIMOTICS SD SH 71 315 Series

Reviews:

Brands by name

Popular brands

Siemens SIMOTICS SD SH 71 315 Series, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS SD SH 71 315 Series

Reviews:

Brands by name

Popular brands