Siemens SIMOTICS CONNECT 400 Operating Instructions Manual Download

Page: 14 / 120

3.2

"SIMOTICS CONNECT 400" connectivity module

The connectivity module mounted on the motor captures important operating and status
information of the motor.

The captured motor data are transmitted to SIDRIVE IQ Fleet via a WLAN interface and analyzed.

Note

The SIMOTICS CONNECT 400 connectivity module can be used in combination with rib-cooled
low-voltage induction motors (see Technical specifications (Page 111)).

Components

The connectivity module encompasses the following components:

• Integrated sensors to measure the motor data

• Data memory

• Processor

• Bluetooth module

• WLAN communication module

• Lithium battery for the power supply

The Connectivity Kit contains the following components in addition to the connectivity module:

• Metal bracket for mounting on the motor housing

• Fastening screws

Description
3.2 "SIMOTICS CONNECT 400" connectivity module

SIMOTICS CONNECT 400

Operating Instructions, 08/2021, A5E50161952B AE

Summary of Contents for SIMOTICS CONNECT 400

























































































































Search results

Summary of Contents for SIMOTICS CONNECT 400

Reviews:

Related manuals for SIMOTICS CONNECT 400

Brands by name

Popular brands

Siemens SIMOTICS CONNECT 400, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS CONNECT 400

Reviews:

Related manuals for SIMOTICS CONNECT 400

Brands by name

Popular brands