manualshive.com logo in svg

Siemens SIMOGEAR BA 203-A, Mounting And Operating Instructions

Share
Download
Siemens SIMOGEAR BA 203-A Mounting And Operating Instructions Download Page 27

Installing

4

4.1

Unpacking

NOTICE
Transport damage impairs the correct function of the geared motor

Never commission faulty or defective motors.

Check the motor for completeness and damage. Report any missing parts or damage 
immediately.

Remove and dispose of the packaging material and transport equipment in compliance with 
regulations.

4.2

General information on installation

Ex-version of gearbox and geared motor
Effect on bearings of stray electric currents from electrical equipment.
When mounting the gearbox on or connecting it to the machine, take care to ensure 
potential equalization. The information on grounding and equipotential bonding 
provided by the motor supplier must be observed.

WARNING

Operating under load

Under load, the system can start or reverse in an uncontrolled fashion.

The entire system must be load-free so that there is no danger during this work.

NOTICE
Destruction caused by welding

Welding destroys the geared parts and bearings.

Do not weld on the gearbox. The gearbox must not be used as a grounding point for welding 
operations.

SIMOGEAR adapters for gearboxes - KS, K2, K3, K4, K5, KQ, KQS, K8, A, AZ
Operating Instructions, 05/2022, A5E37431501A/RS-AL

25

Summary of Contents for SIMOGEAR BA 203-A































































Reviews:

No comments

Brands by name

Popular brands

Load more brands