Siemens SIMATIC TDC System Manual Download

Page: 105 / 228

Signal modules

5.1 SM500 signal module

SIMATIC TDC hardware
System Manual, 08/2017, A5E01114865-AL

105

5.1.3

Status and fault displays

Status displays for SM500

Table 5- 2

Status displays for signal module SM500

LED display

Module status

Off

During voltage run-up

Off

FPGAs are configured, module is not initialized

Off

Module is initialized and operating error-free

After 3.3 V voltage failure

•

Hardware failure => Power-down the rack and replace the SM500

5.1.4

Application notes and immunity to interference

●

Fan operation is required

●

Interference-proof operation is only possible if the SM500 is firmly attached to the rack.

Insert the module and then bolt it onto the rack accordingly (two screw heads, see

Control and display elements (Page 103)).

●

The module may not be inserted or removed while the rack is on live voltage.

Note
For more information on fan operation, refer to chapter "Rack (Page 39)"!
For more information on EMC and environmental conditions, refer to chapter "General

technical specifications (Page 37)"!

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands