Siemens SIMATIC S7-1500R/H Manual Download

Page: 44 / 46

Technical specifications

CPU 1517H-3 PN (6ES7517-3HP00-0AB0)
Equipment Manual, 11/2019, A5E42011886-AB

Article number

6ES7517-3HP00-0AB0

Configuration

Programming

Programming language

–

LAD

Yes

–

FBD

Yes

–

STL

Yes

–

SCL

Yes

–

CFC

–

GRAPH

Yes

Know-how protection

•

User program protection/password protec-

tion

Yes

•

Copy protection

•

Block protection

Yes

Access protection

•

Password for display

Yes

•

Protection level: Write protection

Yes

•

Protection level: Read/write protection

Yes

•

Protection level: Complete protection

Yes

Cycle time monitoring

•

lower limit

adjustable minimum cycle time

•

upper limit

adjustable maximum cycle time

Dimensions

Width

210 mm

Height

147 mm

Depth

129 mm

Weights

Weight, approx.

2 119 g; Interface modules: 2x 18 g

General technical specifications

You can find information on the general technical specifications, such as standards and

approvals, electromagnetic compatibility, protection class, etc. in the system manual for

Redundant System S7-1500R/H

(

https://support.industry.siemens.com/cs/ww/en/view/109754833

Summary of Contents for SIMATIC S7-1500R/H















































Search results

Summary of Contents for SIMATIC S7-1500R/H

Reviews:

Related manuals for SIMATIC S7-1500R/H

Brands by name

Popular brands

Siemens SIMATIC S7-1500R/H, Manual

Search results

Summary of Contents for SIMATIC S7-1500R/H

Reviews:

Related manuals for SIMATIC S7-1500R/H

Brands by name

Popular brands