Siemens SIMATIC S7-1500R/H Manual Download Page 33

Page: 33 / 46

Interrupts, diagnostics, error messages and system events

4.1 Status and error display of the CPU

CPU 1517H-3 PN (6ES7517-3HP00-0AB0)

Equipment Manual, 11/2019, A5E42011886-AB

The following table shows the meaning of the various color combinations for the RUN/STOP,

ERROR and MAINT LEDs.

Table 4- 1

Meaning of the LEDs

RUN/STOP LED

ERROR LED

MAINT LED

Meaning

LED off

Missing or insufficient supply voltage on the CPU.

LED flashes

yellow/green

LED flashes red

LED flashes yellow

Startup (CPU booting)
Test of LEDs during startup, inserting a module.
LED flashing test

LED lit yellow

LED off

LED lit yellow

CPU is in operating state STOP.
Completion of system initialization

LED flashes yellow

LED off

LED lit yellow

CPU executes internal activities in an operating

state

≠

RUN-Redundant.

LED lit yellow

LED flashes red

LED flashes yellow

CPU defective

LED lit yellow

LED off

LED flashes yellow

Firmware update successfully completed.

LED flashes

yellow/green

LED off

LED lit yellow

The primary CPU is in STARTUP operating state.
The backup CPU is in SYNCUP operating state.
The backup CPU has not yet been restarted for

SYNCUP during this phase.

LED flashes yellow

LED off

The CPU performs a warm restart.

LED lit green

LED off

LED lit yellow

Maintenance demanded for the plant.
You need to check/replace the affected hardware

within a short period of time.
The primary CPU is in RUN-Syncup operating

state.
Active Force job
PROFIenergy pause
The primary CPU is in RUN operating state.

LED lit green

LED off

The CPU is in RUN-Redundant operating state.
There are no events, requirements, errors, etc.

LED lit green

LED flashes red

LED off

A diagnostic event is pending in RUN-Redundant

operating state.

LED lit green

LED flashes red

LED lit yellow

A diagnostic event (e.g. failure of an IO device

within the PROFINET ring or no access to

SIMATIC memory card possible

) and mainte-

nance is demanded (e.g. interruption of the

PROFINET ring).

If access to the SIMATIC memory card is not possible in RUN-Redundant (wrong card, card full/write protected), the

system switches to RUN-Solo. The ERROR LED flashes for three seconds. The MAINT LED lights up until the RUN-

Redundant system status is reached again.

Summary of Contents for SIMATIC S7-1500R/H















































Search results

Summary of Contents for SIMATIC S7-1500R/H

Reviews:

Related manuals for SIMATIC S7-1500R/H

Brands by name

Popular brands

Siemens SIMATIC S7-1500R/H, Manual

Search results

Summary of Contents for SIMATIC S7-1500R/H

Reviews:

Related manuals for SIMATIC S7-1500R/H

Brands by name

Popular brands